Browsing by Author "Song, Hyun-Cheol"

Now showing 1 - 6 of 6
  • Thumbnail Image
    3D printed graphene-based self-powered strain sensors for smart tires in autonomous vehicles
    Maurya, Deepam; Khaleghian, Seyedmeysam; Sriramdas, Rammohan; Kumar, Prashant; Kishore, Ravi Anant; Kang, Min-Gyu; Kumar, Vireshwar; Song, Hyun-Cheol; Lee, Seul-Yi; Yan, Yongke; Park, Jung-Min (Jerry); Taheri, Saied; Priya, Shashank (2020-10-26)
    The transition of autonomous vehicles into fleets requires an advanced control system design that relies on continuous feedback from the tires. Smart tires enable continuous monitoring of dynamic parameters by combining strain sensing with traditional tire functions. Here, we provide breakthrough in this direction by demonstrating tire-integrated system that combines direct mask-less 3D printed strain gauges, flexible piezoelectric energy harvester for powering the sensors and secure wireless data transfer electronics, and machine learning for predictive data analysis. Ink of graphene based material was designed to directly print strain sensor for measuring tire-road interactions under varying driving speeds, normal load, and tire pressure. A secure wireless data transfer hardware powered by a piezoelectric patch is implemented to demonstrate self-powered sensing and wireless communication capability. Combined, this study significantly advances the design and fabrication of cost-effective smart tires by demonstrating practical self-powered wireless strain sensing capability. Designing efficient sensors for smart tires for autonomous vehicles remains a challenge. Here, the authors present a tire-integrated system that combines direct mask-less 3D printed strain gauges, flexible piezoelectric energy harvester for powering the sensors and secure wireless data transfer electronics, and machine learning for predictive data analysis.
  • Thumbnail Image
    Compositionally Graded Multilayer Ceramic Capacitors
    Song, Hyun-Cheol; Zhou, Jie E.; Maurya, Deepam; Yan, Yongke; Wang, Yu U.; Priya, Shashank (Springer Nature, 2017-09-27)
    Multilayer ceramic capacitors (MLCC) are widely used in consumer electronics. Here, we provide a transformative method for achieving high dielectric response and tunability over a wide temperature range through design of compositionally graded multilayer (CGML) architecture. Compositionally graded MLCCs were found to exhibit enhanced dielectric tunability (70%) along with small dielectric losses (< 2.5%) over the required temperature ranges specified in the standard industrial classifications. The compositional grading resulted in generation of internal bias field which enhanced the tunability due to increased nonlinearity. The electric field tunability of MLCCs provides an important avenue for design of miniature filters and power converters.
  • Thumbnail Image
    Correlation between tunability and anisotropy in magnetoelectric voltage tunable inductor (VTI)
    Yan, Yongke; Geng, Liwei D.; Zhang, Lujie; Gao, Xiangyu; Gollapudi, Sreenivasulu; Song, Hyun-Cheol; Dong, Shuxiang; Sanghadasa, Mohan; Ngo, Khai D. T.; Wang, Yu U.; Priya, Shashank (Springer Nature, 2017-11-22)
    Electric field modulation of magnetic properties via magnetoelectric coupling in composite materials is of fundamental and technological importance for realizing tunable energy efficient electronics. Here we provide foundational analysis on magnetoelectric voltage tunable inductor (VTI) that exhibits extremely large inductance tunability of up to 1150% under moderate electric fields. This field dependence of inductance arises from the change of permeability, which correlates with the stress dependence of magnetic anisotropy. Through combination of analytical models that were validated by experimental results, comprehensive understanding of various anisotropies on the tunability of VTI is provided. Results indicate that inclusion of magnetic materials with low magnetocrystalline anisotropy is one of the most effective ways to achieve high VTI tunability. This study opens pathway towards design of tunable circuit components that exhibit field-dependent electronic behavior.
  • Thumbnail Image
    Lead-free epitaxial ferroelectric material integration on semiconducting (100) Nb-doped SrTiO3 for low-power non-volatile memory and efficient ultraviolet ray detection
    Kundu, Souvik; Clavel, Michael B.; Biswas, Pranab; Chen, Bo; Song, Hyun-Cheol; Kumar, Prashant; Halder, Nripendra N.; Hudait, Mantu K.; Banerji, Pallab; Sanghadasa, Mohan; Priya, Shashank (Springer Nature, 2015-07-23)
    We report lead-free ferroelectric based resistive switching non-volatile memory (NVM) devices with epitaxial (1-x)BaTiO3-xBiFeO(3) (x = 0.725) (BT-BFO) film integrated on semiconducting (100) Nb (0.7%) doped SrTiO3 (Nb: STO) substrates. The piezoelectric force microscopy (PFM) measurement at room temperature demonstrated ferroelectricity in the BT-BFO thin film. PFM results also reveal the repeatable polarization inversion by poling, manifesting its potential for read-write operation in NVM devices. The electroforming-free and ferroelectric polarization coupled electrical behaviour demonstrated excellent resistive switching with high retention time, cyclic endurance, and low set/reset voltages. X-ray photoelectron spectroscopy was utilized to determine the band alignment at the BT-BFO and Nb: STO heterojunction, and it exhibited staggered band alignment. This heterojunction is found to behave as an efficient ultraviolet photo-detector with low rise and fall time. The architecture also demonstrates half-wave rectification under low and high input signal frequencies, where the output distortion is minimal. The results provide avenue for an electrical switch that can regulate the pixels in low or high frequency images. Combined this work paves the pathway towards designing future generation low-power ferroelectric based microelectronic devices by merging both electrical and photovoltaic properties of BT-BFO materials.
  • Thumbnail Image
    Piezoelectric-based Multi-Scale Multi-Environment Energy Harvesting
    Song, Hyun-Cheol (Virginia Tech, 2017-08-10)
    Energy harvesting is a technology for generating electrical power from ambient or wasted energy. It has been investigated extensively as a means of powering small electronic devices. The recent proliferation of devices with ultra-low power consumption - devices such as RF transmitters, sensors, and integrated chipsets - has created new opportunities for energy harvesters. There is a variety of ambient energies such as vibration, thermal, solar, stray current, etc. Depending on energy sources, different kinds of energy conversion mechanism should be employed. For energy harvesters to become practical, their energy conversion efficiency must improve. This efficiency depends upon advances in two areas: the system or structural design of the energy harvester, and the properties of the materials employed in energy conversion. This dissertation explores developments in both areas. In the first area, the role of nano-, micro-, and bulk structure of the energy conversion materials were investigated. In the second area, piezoelectric energy harvesters and a magneto-thermoelectric generator are treated from the perspective of system design. In the area of materials development, PbTiO3 (PTO) nanostructures consisting of nanofibers and three-dimensional (3-D) nanostructure arrays were hydrothermally synthesized. The growth mechanism of the PTO nanofibers and 3-D nanostructures were investigated experimentally and theoretically. The PTO nanostructures were composed of oriented PTO crystals with high tetragonality; these arrays could be promising candidates for nanogenerators. Different designs for energy harvesters were explored as a means of improving energy conversion efficiency. Piezoelectric energy harvesters were designed and constructed for applications with a low frequency vibrational energy and for applications with a broadband energy spectrum. A spiral MEMS piezoelectric energy harvester design was fabricated using a silicon MEMS process and demonstrated to extract high power density at ultra-low resonance frequencies and low acceleration conditions. For a broadband energy harvester, a magnetically-coupled array of oscillators was designed and built that broadened the harvester's effective resonance frequency with considerably improved output power. A new design concept for thermal energy harvesting that employs a magneto-thermoelectric generator (MTG) design was proposed. The MTG exploits a thermally-induced second order phase transition in a soft magnetic material near the Curie temperature. The MTG harvested electric power from oscillations of the soft magnet between hot and cold sources. For the MTG design, suitable soft magnetic materials were selected and developed using La0.85Sr0.15MnO3-Ni0.6Cu0.2Zn0.2Fe2O4 magnetic composites. The MTG was fabricated from a PVDF cantilever and a gadolinium (Gd) soft magnetic material. The feasibility of the design for harvesting energy from the waste heat was demonstrated by attaching an MTG array to a computer CPU.
  • Thumbnail Image
    Thermo-Magneto-Electric Generator Arrays for Active Heat Recovery System
    Chun, Jinsung; Song, Hyun-Cheol; Kang, Min-Gyu; Kang, Han Byul; Kishore, Ravi Anant; Priya, Shashank (Springer Nature, 2017-02-01)
    Continued emphasis on development of thermal cooling systems is being placed that can cycle low grade heat. Examples include solar powered unmanned aerial vehicles (UAVs) and data storage servers. The power efficiency of solar module degrades at elevated temperature, thereby, necessitating the need for heat extraction system. Similarly, data centres in wireless computing system are facing increasing efficiency challenges due to high power consumption associated with managing the waste heat. We provide breakthrough in addressing these problems by developing thermo-magneto-electric generator (TMEG) arrays, composed of soft magnet and piezoelectric polyvinylidene difluoride (PVDF) cantilever. TMEG can serve dual role of extracting the waste heat and converting it into useable electricity. Near room temperature second-order magnetic phase transition in soft magnetic material, gadolinium, was employed to obtain mechanical vibrations on the PVDF cantilever under small thermal gradient. TMEGs were shown to achieve high vibration frequency at small temperature gradients, thereby, demonstrating effective heat transfer.