Show simple item record

dc.contributor.authorMcCann, Martha Maryen
dc.date.accessioned2014-03-14T20:10:33Zen
dc.date.available2014-03-14T20:10:33Zen
dc.date.issued2004-03-29en
dc.identifier.otheretd-04232004-091718en
dc.identifier.urihttp://hdl.handle.net/10919/27170en
dc.description.abstractNanoindentation is an increasingly used tool to investigate the mechanical properties of very small volumes of material. Gold single crystals were chosen as a model system for surface modification studies, because of the electrochemical advantages and the simple structure of the material. Experiments on these samples displayed a spectrum of residual deformation, with measured hardness values on the same surface differing by over a factor of two. The yield point also exhibited considerable variation, but the depth of penetration was independent of this elasticâ plastic transition. The onset of plastic deformation in these tests is observed at stress levels on the order of the theoretical yield strength. There are a limited number of defects in a single crystal specimen of gold, especially on the length scale required to influence nearly every indentation experiment. A test matrix was designed to change the concentrations of possible defects in a sample (dislocations, vacancies, and structural features), by altering some of the surface preparation parameters. The results of these experiments were extremely consistent. Observed trends within the matrix, combined with the observations of reduced hardness and earlier plasticity when compared to the preliminary testing, indicate a decline in the structural continuity of the sample. This is surprising considering the extensive material removal and thermal history of some of these surfaces. There is no indication of a cause for the dramatic inconsistencies in mechanical properties observed in preliminary testing, but a consistent surface enables the study of intentional modifications. Changes in contact area that were undetectable in preliminary results now demonstrate predictable shifts in hardness values. The deposition of a single monolayer of gold oxide raised the average load at yield by a factor of three and increased the hardness by over 26%. Attributing this change to the oxide is corroborated by the reduction of hardness when the oxide is stripped. Similar behavior is observed when a lead monolayer is deposited and tested ex-situ. It is surprising that layers <0.5 nm in thickness would have such a dramatic influence on indentation tests at least 35 nm deep. This indicates that no surface layer can be ignored at this scale. These experiments demonstrate that there is still much to be learned about nanoscale deformation mechanisms.en
dc.publisherVirginia Techen
dc.relation.haspartNanoindentation-of-Gold-Single-Crystals.pdfen
dc.rightsIn Copyrighten
dc.rights.urihttp://rightsstatements.org/vocab/InC/1.0/en
dc.subjectSurface Structureen
dc.subjectElectrochemical Modificationen
dc.subjectYield Variabilityen
dc.subjectNanoindentationen
dc.subjectHardness Variabilityen
dc.subjectGolden
dc.titleNanoindentation of Gold Single Crystalsen
dc.typeDissertationen
dc.contributor.departmentMaterials Science and Engineeringen
dc.description.degreePh. D.en
thesis.degree.namePh. D.en
thesis.degree.leveldoctoralen
thesis.degree.grantorVirginia Polytechnic Institute and State Universityen
thesis.degree.disciplineMaterials Science and Engineeringen
dc.contributor.committeechairCorcoran, Sean G.en
dc.contributor.committeememberAning, Alexander O.en
dc.contributor.committeememberReynolds, William T. Jr.en
dc.contributor.committeememberKampe, Stephen L.en
dc.contributor.committeememberFarkas, Dianaen
dc.identifier.sourceurlhttp://scholar.lib.vt.edu/theses/available/etd-04232004-091718/en
dc.date.sdate2004-04-23en
dc.date.rdate2004-04-29en
dc.date.adate2004-04-29en


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record