The Use of Stormwater Modeling for Design and Performance Evaluation of Best Management Practices at the Watershed Scale

dc.contributor.authorHouston, Edward Brianen
dc.contributor.committeechairKibler, David F.en
dc.contributor.committeememberHeatwole, Conrad D.en
dc.contributor.committeememberLoganathan, G. V.en
dc.contributor.departmentCivil Engineeringen
dc.date.accessioned2014-03-14T20:44:31Zen
dc.date.adate2006-10-02en
dc.date.available2014-03-14T20:44:31Zen
dc.date.issued2006-08-29en
dc.date.rdate2006-10-02en
dc.date.sdate2006-08-30en
dc.description.abstractThe use of best management practices or BMPs to treat urban stormwater runoff has been pervasive for many years. Extensive research has been conducted to evaluate the performance of individual BMPs at specific locations; however, little research has been published that seeks to evaluate the impacts of small, distributed BMPs throughout a watershed at the regional level. To address this, a model is developed using EPA SWMM 5.0 for the Duck Pond watershed, which is located in Blacksburg, Virginia and encompasses much of the Virginia Polytechnic and State Institute's campus and much of the town of Blacksburg as well. A variety of BMPs are designed and placed within the model. Several variations of the model are created in order to test different aspects of BMP design and to test the BMP modeling abilities of EPA SWMM 5.0. Simulations are performed using one-hour design storms and yearlong hourly rainfall traces. From these simulations, small water quality benefits are observed at the system level. This is seen as encouraging, given that a relatively small amount of the total drainage area is controlled by BMPs and that the BMPs are not sited in optimal locations. As expected, increasing the number of BMPs in the watershed generally increases the level of treatment. The use of the half-inch rule in determining the required water quality volume is examined and found to provide reasonable results. The design storm approach to designing detention structures is also examined for a two-pond system located within the model. The pond performances are examined under continuous simulation and found to be generally adequate for the simulated rainfall conditions, although they do under-perform somewhat in comparison to the original design criteria. The usefulness of EPA SWMM 5.0 as a BMP modeling tool is called into question. Many useful features are identified, but so are many limitations. Key abilities such as infiltration from nodes or treatment in conduit flow are found to be lacking. Pollutant mass continuity issues are also encountered, making specific removal rates difficult to define.en
dc.description.degreeMaster of Scienceen
dc.identifier.otheretd-08302006-185047en
dc.identifier.sourceurlhttp://scholar.lib.vt.edu/theses/available/etd-08302006-185047/en
dc.identifier.urihttp://hdl.handle.net/10919/34850en
dc.publisherVirginia Techen
dc.relation.haspartHalfInch.inpen
dc.relation.haspartInfiltrate.inpen
dc.relation.haspartTreatmentNode.inpen
dc.relation.haspartthesis.pdfen
dc.relation.haspartbase.inpen
dc.relation.haspartOneInch.inpen
dc.rightsIn Copyrighten
dc.rights.urihttp://rightsstatements.org/vocab/InC/1.0/en
dc.subjectBMP modelingen
dc.subjectcontinuous modelingen
dc.subjectEPA SWMMen
dc.titleThe Use of Stormwater Modeling for Design and Performance Evaluation of Best Management Practices at the Watershed Scaleen
dc.typeThesisen
thesis.degree.disciplineCivil Engineeringen
thesis.degree.grantorVirginia Polytechnic Institute and State Universityen
thesis.degree.levelmastersen
thesis.degree.nameMaster of Scienceen

Files

Original bundle
Now showing 1 - 5 of 6
Name:
HalfInch.inp
Size:
498.74 KB
Format:
Unknown data format
Name:
Infiltrate.inp
Size:
498.84 KB
Format:
Unknown data format
Name:
TreatmentNode.inp
Size:
504.42 KB
Format:
Unknown data format
Loading...
Thumbnail Image
Name:
thesis.pdf
Size:
3.92 MB
Format:
Adobe Portable Document Format
Name:
base.inp
Size:
485.25 KB
Format:
Unknown data format

Collections