Browsing by Author "Li, Yi"

Now showing 1 - 4 of 4
  • Thumbnail Image
    Effective Simplified Finite Element Tire Models for Vehicle Dynamics Simulation
    Li, Yi (Virginia Tech, 2017-09-15)
    The research focuses on developing a methodology for modeling a pneumatic bias-ply tire with the finite element method for vehicle dynamics simulation. The tire as a load-carrying member in a vehicle system deserves emphasized formulation especially for the contact patch because its representation of mechanics in the contact patch directly impacts the handling and ride performance of a vehicle. On the other hand, the load transfer from the contact patch to the wheel hub is necessary for determining the inputs to a chassis. A finite element (FE) tire model has strong capability to handle these two issues. However, the high cost of computing resources restrains its application mainly in the tire design domain. This research aims to investigate how to balance the complexity of a simplified FE tire model without diminishing its capability towards representing the load transmission for vehicle dynamics simulation. The traditional FE tire model developed by tire suppliers usually consists of an extremely large number of elements, which makes it impossible to be included in a full-vehicle dynamics simulation. The material properties required by tire companies' FE tire models are protected. The car companies have an increasing need for a physical-based tire model to understand more about the interaction between the tire and chassis. A gap between the two sides occurs because the model used for tire design cannot directly help car companies for their purpose. All of these reasons motivate the current research to provide a solution to narrow this gap. Other modern tire models for vehicle dynamics, e.g. FTire or TAME, require a series of full-tire tests to calibrate their model parameters, which is expensive and time-consuming. One great merit of the proposed simplified FE tire model is that determining model inputs only requires small-scale specimen tests instead of full-tire tests. Because much of the usability of a model hinges on whether its input parameters are easily determined, this feature makes the current model low cost and easily accessible in the absence of proprietary information from the tire supplier. A Hoosier LC0 racing tire was selected as a proof of modeling concept. All modeling work was carried out using the general purpose commercial software Abaqus. The developed model was validated through static load-deflection test data together with Digital Image Correlation (DIC) data. The finite element models were further evaluated by predicting the traction/braking and cornering tire forces against Tire Test Consortium (TTC) data from the Calspan flat-track test facility. The emphasis was put on modeling techniques for the transient response due to the lack of available test data. The in-plane and out-of-plane performance of the Hoosier tire on the full-tire test data is used for model validation, not for "calibrating" the model. The agreement between model prediction and physical tests demonstrate the effectiveness of the proposed methodology.
  • Thumbnail Image
    Genome sequences of wild and domestic bactrian camels
    Jirimutu; Wang, Zhen; Ding, Guohui; Chen, Gangliang; Sun, Yamin; Sun, Zhihong; Zhang, Heping; Wang, Lei; Hasi, Surong; Zhang, Yan; Li, Jianmei; Shi, Yixiang; Xu, Ze; He, Chuan; Yu, Siriguleng; Li, Shengdi; Zhang, Wenbin; Batmunkh, Mijiddorj; Ts, Batsukh; Narenbatu; Unierhu; Bat-Ireedui, Shirzana; Gao, Hongwei; Baysgalan, Banzragch; Li, Qing; Jia, Zhiling; Turigenbayila; Subudenggerile; Narenmanduhu; Wang, Zhaoxia; Wang, Juan; Pan, Lei; Chen, Yongcan; Ganerdene, Yaichil; Dabxilt; Erdemt; Altansha; Altansukh; Liu, Tuya; Cao, Minhui; Aruuntsever; Bayart; Hosblig; He, Fei; Zha-ti, A.; Zheng, Guangyong; Qiu, Feng; Sun, Zikui; Zhao, Lele; Zhao, Wenjing; Liu, Baohong; Li, Chao; Chen, Yunqin; Tang, Xiaoyan; Guo, Chunyan; Liu, Wei; Ming, Liang; Temuulen; Cui, Aiying; Li, Yi; Gao, Junhui; Li, Jing; Wurentaodi; Niu, Shen; Sun, Tao; Zhai, Zhengxiao; Zhang, Min; Chen, Chen; Baldan, Tunteg; Bayaer, Tuman; Li, Yixue; Meng, He (Springer Nature, 2012-11)
    Bactrian camels serve as an important means of transportation in the cold desert regions of China and Mongolia. Here we present a 2.01 Gb draft genome sequence from both a wild and a domestic bactrian camel. We estimate the camel genome to be 2.38 Gb, containing 20,821 protein-coding genes. Our phylogenomics analysis reveals that camels shared common ancestors with other even-toed ungulates about 55-60 million years ago. Rapidly evolving genes in the camel lineage are significantly enriched in metabolic pathways, and these changes may underlie the insulin resistance typically observed in these animals. We estimate the genome-wide heterozygosity rates in both wild and domestic camels to be 1.0 x 10(-3). However, genomic regions with significantly lower heterozygosity are found in the domestic camel, and olfactory receptors are enriched in these regions. Our comparative genomics analyses may also shed light on the genetic basis of the camel's remarkable salt tolerance and unusual immune system.
  • Thumbnail Image
    Sterically Crowded Copolymers Based on Functionalized Stilbenes
    Li, Yi (Virginia Tech, 2012-02-17)
    The research in this dissertation is focused on the synthesis and characterization of sterically crowded, precisely charged polyelectrolytes based on substituted stilbene comonomers. New sterically crowded polyelectrolytes based on functionalized stilbenes with maleic anhydride or functionalized N-phenylmaleimides were prepared via a "protected" precursor polymer strategy. The polyelectrolyte precursors readily dissolved in organic solvents and were characterized by 1H NMR, SEC, TGA, and DSC. The polyelectrolytes were obtained via simple deprotection chemistries. The use of different combinations of the donor-acceptor comonomer pairs and the alternating copolymerization of these comonomers lead to precise control over charge density and placement of charged groups along the polymer backbone. Analogous styrenic copolymers, for direct comparison to the stilbene structures, were also prepared. Broad peaks in 1H NMR spectra were observed. There were no thermal transitions measured by DSC below the degradation temperature. A strong polyelectrolyte effect, for both stilbene and styrene copolymers, occurred in deionized water and was suppressed by adding NaCl to the polymer solution. These results are not consistent with "rigid" rod polyelectrolytes in which chain collapse in the presence of added salt and chain expansion on dilution should not be observed. In response to these observations persistence length measurements were conducted on the stilbene and styrene copolymers to assess directly the steric crowding effect of added phenyl groups in stilbene copolymers. Both SEC and SAXS measurements were used to obtain persistence lengths. The results from three different approaches, Bohdanecký, graphical and Sharp and Bloomfield Global, were in good agreement. The persistence lengths of stilbene containing copolymers range from 3 to 6 nm and the added phenyl groups increase the rigidity of the polymer chain by about 30-50%. This puts these polymers into a broadly defined "semi-rigid" category of polymers and is consistent with the solution polyelectrolyte effect observed. In dilute solution characterization of stilbene containing polyanions, a 2-step dissociation behavior was observed for the two adjacent carboxylic acids in maleic acid containing polyanions. Stilbene polyanion solutions showed high Rh values in deionized water as shown by DLS measurements and a decrease of Rh values followed by aggregation upon gradual addition of salt. Bimodal peaks were observed in SEC measurements with the copolymer of 4-methylstilbene and maleic anhydride. DLS measurements indicated interchain aggregation as the origin of the apparent high molecular weight fraction. The antiviral activity of the polyanion based on sodium 4-styrenesulfonate and N-(4-sodium sulfophenyl)maleimide was found to be ~50 times higher than the microbicide, sodium poly(styrene sulfonate). The early study of antiviral activities of carboxylated stilbene and styrene polyanions also showed promising results. The synthesis of methyl sulfonate ester-functionalized polyanion precursors was attempted because they can be characterized without the complications caused by directly using charged sulfonate groups.
  • Thumbnail Image
    Studies Related to the Alternating Copolymerization of Substituted Stilbenes
    Li, Yi (Virginia Tech, 2009-05-07)
    Stilbene containing polymers are a group of interesting and versatile polymers. The pendent phenyl ring along the polymer backbone can impart unusual rigidity to the polymer backbone due to steric repulsion. By functionalizing stilbene, a variety of functional groups and ionic groups can be precisely placed along the polymer chain with tunable charge density. Therefore, stilbene containing polymers are potentially rod-like polyelectrolytes with controllable charges and charge density. They are the basis of a novel group of rigid synthetic polyelectrolytes and can be used for furthering our knowledge of rigid polyelectrolytes. A novel series of methyl substituted stilbenes were synthesized and copolymerized with maleic anhydride. A conversion-time study was undertaken to understand the methyl substituent effect on copolymerization rates. Methyl substituted stilbene-maleic anhydride copolymer compositions were determined by quantitative ¹³C 1D NMR. SEC measurements showed the weight average molecular weights of these copolymers vary from 3 000 to over 1 000 000 g/mol. No glass transition temperature or crystalline melting temperature was observed between 0 °C and 250 °C by DSC. TGA showed that these polymers have 5% weight loss around 290 °C. Precursors to a polycation and a polyanion based on functionalized stilbenes and maleimides have been prepared: poly(di-t-butyl-(E)-4,4′-stilbenedicarboxylate-co- N-(4-(t-butoxycarbonyl)phenyl)maleimide) and poly(N,N,Nâ ,Nâ -tetraalkyl-4,4′-di- aminostilbenes-co-N-4-(N′,N′-dimethylaminophenyl)-maleimide). These copolymer precursors were characterized by ¹H NMR, SEC, TGA, and DSC. The ¹H NMR spectrum indicated the rigidity of copolymer backbones. SEC measurements showed the weight average molecular weights of these copolymers vary from 5 000 to 11 700 g/mol. No glass transition temperature or crystalline melting temperature was observed between 0 °C and 175 °C by DSC for poly(di-t-butyl-(E)-4,4′-stilbenedicarboxylate-co-N-(4-(t-butoxy- carbonyl)phenyl)maleimide). TGA showed that this polymer has 5% weight loss around 210 °C and 26% weight loss on the first stage of decomposition which corresponds to elimination of t-butyl functional group in the copolymer. The homopolymerization of EMS-III via free radical polymerization, anionic polymerization and cationic polymerization was attempted. However, no polymer was obtained from any of these polymerization methods. In anionic polymerization, the solution changed to red upon the addition of the initiator sec-bu-Li, indicating the successful addition of the sec-bu-Li to EMS-III. However, the initiated monomer did not propagate to form homopolymer.