VTechWorks Repository :: Browsing by Author "Renneckar, Scott Harold"

Browsing by Author "Renneckar, Scott Harold"

Now showing 1 - 20 of 21

Application of Functional Amyloids in Morphological Control and in Self-assembled Composites
Claunch, Elizabeth Carson (Virginia Tech, 2013-05-14)
Amyloids are self-assembled protein materials containing beta-sheets. While most studies focus on amyloids as the pathogen in neurodegenerative disease, there are instances of "functional" amyloids used to preserve life. Functional amyloids serve as an inspiration in materials design. In this study, it is shown that wheat gluten (WG) and gliadin:myoglobin (Gd:My) amyloid morphology can be varied from predominantly fibrillar at low polypeptide concentration to predominantly globular at high polypeptide concentration as measured at the nanometer scale using atomic force microscopy (AFM). The ability to control the morphology of a material allows control of its properties. Fourier transform infrared (FTIR) spectroscopy shows that at low concentration, fibrils require interdigitation of methyl groups on alanine (A), isoleucine (I), leucine (L), and valine (V). At higher concentration, globules do not have the same interdigitation of methyl groups but more random hydrophobic interactions. The concentration dependence of the morphology is shown as a kinetic effect where many polypeptides aggregate very quickly through hydrophobic interactions to produce globules while smaller populations of polypeptides aggregate slowly through well-defined hydrophobic interactions to form fibrils. Functional amyloids also provide a means of creating a low energy process for composites. Poor fiber/matrix bonding and processing degradation have been observed in previous WG based composites. This study aims to improve upon these flaws by implementing a self-assembly process to fabricate self-reinforced wheat gluten composites. These composites are processed in aqueous solution at neutral pH by allowing the fibers to form in a matrix of unassembled peptides. The fiber and the matrix are formed from the same solution, thus the two components create a compatible system with ideal interfacial interaction for a composite. The fibers in the composite are about 10 microns in diameter and can be several millimeters long. It has been observed that the number of fibers present along the fracture surface influences the modulus of the composite. In this study, self-assembled wheat gluten composites are formed and then characterized with 3-point bend (3PB) mechanical testing, scanning electron microscopy (SEM), and Fourier transform infrared (FTIR) spectroscopy.
Bio-inspired Cellulose Nanocomposites
Pillai, Karthik (Virginia Tech, 2011-04-26)
Natural composites like wood are scale-integrated structures that range from molecular to the macroscopic scale. Inspired by this design, layer-by-layer (LbL) deposition technique was used to create lignocellulosic composites from isolated wood polymers namely cellulose and lignin, with a lamellar architecture. In the first phase of the study, adsorption of alkali lignin onto cationic surfaces was investigated using a quartz crystal microbalance with dissipation monitoring (QCM-D). Complete coverage of the cationic surface with alkali lignin occured at low solution concentration; large affinity coefficients were calculated for this system at differing pH levels. Adsorption studies with organosolv lignin in an organic solvent, and spectroscopic analysis of mixtures of cationic polymer with alkali lignin revealed a non-covalent interaction. The work demonstrated how noncovalent interactions could be exploited to molecular organize thin polyphenolic biopolymers on cationic surfaces. The second phase of the study examined the adsorption steps during the LbL assembly process to create novel lignocellulosic composites. LbL assembly was carried out using oxidized nanocellulose (NC) and lignin, along with a cationic polymer poly(diallyldimethylammonium chloride) (PDDA). QCM-D was used to follow the sequential adsorption process of the three different polymers. Two viscoelastic models, namely Johannsmann and Voigt, were respectively used to calculate the areal mass and thickness of the adsorbed layers. Atomic force microscopy studies showed a complete coverage of the surface with lignin in all the disposition cycles, however, surface coverage with NC was seen to increase with the number of layers. Free-standing composite films were obtained when the LbL process was carried out for 250 deposition cycles (500 bilayers) on a cellulose acetate substrate, following the dissolution of the substrate in acetone. Scanning electron microscopy of the cryo-fractured cross-sections showed a lamellar structure, and the thickness per adsorption cycle was estimated to be 17 nm. The third phase of the study investigated the effect of LbL ordering of the polymers versus a cast film composed of a blended mixture of the polymers, using dynamic mechanical analysis. A tan ï ¤ peak was observed in the 30 – 40 ºC region for both films, which was observed in the neat NC film. Heating of the samples under a compressive force produced opposite effects in the films, as the LbL films exhibited swelling, whereas the cast films showed densification. The apparent activation energy of this transition (65 – 80 kJ mol-1) in cast films, calculated based on the Arrhenius equation was found to be coincident to those reported for the ï ¢ transition of amorphous cellulose. The peak was seen to disappear in case of LbL films in the second heat, whereas it was recurring in case of cast films of the blended mixture, and neat NC films. Altogether, the together the work details a novel path to integrate an organized lignin and cellulose molecular structure, albeit modified from their native form, into a three-dimensional composite material.
Biopolymer Structure Analysis and Saccharification of Glycerol Thermal Processed Biomass
Zhang, Wei (Virginia Tech, 2015-01-31)
Glycerol thermal processing (GTP) is studied as a novel biomass pretreatment method in this research with the purposes to facilitate biopolymer fractionation and biomass saccharification. This approach is performed by treating sweet gum particles on polymer processing equipment at high temperatures and short times in the presence of anhydrous glycerol. Nine severity conditions are studied to assess the impact of time and temperature during the processing on biopolymer structure and conversion. The GTP pretreatment results in the disruption of cell wall networks by increasing the removal of side-chain sugars and lignin-carbohydrate linkages based on severity conditions. After pretreatment, 41% of the lignin and 68% of the xylan is recovered in a dry powdered form by subsequent extractions without additional catalysts, leaving a relatively pure cellulose fraction, 84% glucan, as found in chemical pulps. Lignin structural analysis indicated GTP processing resulted in extensive degradation of B-aryl ether bonds through the C-y elimination, followed by abundant phenolic hydroxyl liberation. At the same time, condensation occurred in the GTP lignin, providing relatively high molecular weight, near to that of the enzymatic mild acidolysis lignin. Better thermal stability was observed for this GTP lignin. In addition to lignin, xylan was successfully isolated as another polymer stream after GTP pretreatment. The recovered water insoluble xylan (WIX) was predominant alkali soluble fraction with a maximum purity of 84% and comparable molecular weight to xylan isolated from non-pretreated fibers. Additionally, the narrow molecular weight distribution of recovered WIX, was arisen from the pre-extraction of low molecular weight water-soluble xylan. Additionally, a 20-fold increase of the ultimate enzymatic saccharification for GTP pretreated biomass was observed even with significant amounts of lignin and xylan remaining on the non-extracted fiber. The shear and heat processing caused a disintegrated cell wall structure with formation of biomass debris and release of cellulose fibrils, enhancing surface area and most likely porosity. These structural changes were responsible for the improved biomass digestibility. Additionally, no significant inhibitory compounds for saccharification are produced during GTP processing, even at high temperatures. While lignin extraction did not promote improvement in hydrolysis rates, further xylan extraction greatly increases the initial enzymatic hydrolysis rate and final level of saccharification. The serial of studies fully demonstrate glycerol thermal processing as a novel pretreatment method to enhance biomass saccharification for biofuel production, as well as facilitate biopolymer fractionation. Moreover, the study shows the impact of thermally introduced structural changes to wood biopolymers when heated in anhydrous environments in the presence of hydrogen bonding solvent.
Characterization of Laser Modified Surfaces for Wood Adhesion
Dolan, Jeffrey Alan (Virginia Tech, 2014-07-01)
The controlled degradation of wood surfaces with infrared light from a CO2 pulsed laser facilitated adhesion without the use of additional resins. Laser modification creates a surface phenomenon that physically and chemically alters the natural biopolymer organization of lignocellulosic materials in a way that promotes adhesion when hot pressed using typical industrial equipment. Laser optimization was determined through mechanical and microscopic observation. It was determined that a mild level of laser surface modification (scale of 30 W/mm2) resulted in the highest bond-line strength. The large spot size of the laser beam resulted in evenly modified surfaces. Surface analysis revealed that laser modification changed native wood morphology, hydrolyzed and vaporized hemicellulose, and enriched the surface with cellulose II and lignin. Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy (ATR FTIR) was used to analyze the bulk of the laser material. This experiment revealed a change in the hydroxyl region related to hydrogen bonding conformations between wood polymers, mainly cellulose. X-ray photoelectron spectroscopy (XPS) provided an elemental composition of the top 5 nanometers of the surface, which resulted in increased carbon-carbon/carbon-hydrogen linkages and decreased oxygen containing bonds due to laser ablation. Static acid-base contact angle analysis was conducted using three probe liquids to find the Lewis acid, Lewis base, and dispersion components of the top nanometer of surface chemistry. Contact angle analysis revealed laser modified samples had a surface free energy that remained similar to the control wood sample. In addition, the dispersion component of the surface free energy increased due to laser ablation while acid-base components were reduced. Atomic force microscopy (AFM) visually displays a reduction in surface roughness due to the laser technique. An additional set of experiments like thermal gravimetric analysis, thermal pre and post treatments, and heated ATR FTIR and XPS support findings which require more investigation into this adhesion phenomenon.
Effect of de novo peptide properties on self-assembling large amyloid fibers
Rippner, Caitlin Marie Weigand (Virginia Tech, 2013-05-14)
Amyloid aggregation involves the spontaneous formation of fibers from misfolded proteins. This process requires low energy input, results in robust fibers, and is thus of interest from a materials manufacturing perspective. The effect of glutamine content and hydrophobicity of template peptides on amyloid aggregation of a template-peptide system involving myoglobin was studied at near-physiological conditions by Fourier transform infrared spectroscopy, atomic force microscopy, field emission scanning electron microscopy, and nanoindentation. Hydrophobic interactions were found to be important for controlled hierarchical fiber growth via a cooperative mechanism, with the largest effect in myoglobin mixtures. Hydrophobic packing increased for most systems as aggregation progressed. The largest changes in structure occurred upon drying. When myoglobin was present with the highest glutamine-containing template (P7), the high glutamine peptide was not effective as a template, since it appeared to prefer self-catalysis. A low level of glutamine in some unordered templates was insufficient for amyloid development. However, templating was more important in glutamine-free templates mixed with myoglobin, which formed fibers with a surprisingly high elastic modulus. This may have been due to template patterning. Nanoindentation results confirmed that glutamine blocks were not necessary for strong intermolecular interactions and cooperative fibril formation.
Effect of surface modifications on biodegradation of nanocellulose and microbial response
Singh, Gargi (Virginia Tech, 2015-09-22)
History teaches us that novel materials, such as chlorofluorocarbon and asbestos, can have dire unintended consequences to human and environmental health. The exponential growth of the field of nanotechnology and the products developed along the way provide the opportunity for a new paradigm of design thinking, in which human and environmental impacts are considered early on in product development. In particular, nanocellulose is touted as a promising green nanomaterial, as it is sourced from an effectively inexhaustible feedstock of wood-based cellulose and is assumed to be harmless to the environment since it is derived from a natural material and assumed to be biodegradable. The various forms of nanocellulose possess an impressive diversity of properties, making it suitable for a wide variety of applications such as drug delivery, reinforcement, food additives, and iridescent make-up. However, as nanomaterials can have different properties relative to their bulk form, it is questionable whether they are truly environmentally friendly, particularly in terms of their biodegradability and potential impacts to receiving environments. Given the projected mass-scale application of nanocellulose and the inevitability of its subsequent release into environment, the purpose of this study was to determine the biodegradability of nanocellulose and the response of environmentally-relevant microbial communities. Specifically, it was hypothesized that cellulose in the nano size range would display distinct biodegradation patterns and rates, relative to larger forms of cellulose. Further, it was hypothesized that modification of nanocellulose, in terms of morphology and surface properties (e.g., charge), would further influence its biodegradability. Wetlands and anaerobic digesters were selected as two environmentally-relevant receiving environments that also play critical roles in global carbon turnover. To examine the biodegradability of nanocellulose, two distinct microbial consortia were enriched from wetland (W) and anaerobic digester (AD) inocula and applied in parallel experiments. The consortia were grown under anaerobic conditions with microcrystalline cellulose as the sole carbon substrate over a period of 246 days before being aliquoted to microcosms for subsequent biodegradation assays. Various forms of nanocellulose were spiked into the microcosms and compared with microcrystalline cellulose as a non nano reference. Microcosms were sacrificed in triplicate with time to monitor cellulose degradation as well as various measures of microbial community response. Microbial communities were characterized in terms of gene markers for total bacteria (16S rRNA genes) and anaerobic cellulose degraders (glycoside hydrolase family 48 genes, i.e., cel48) as well as high throughput amplicon sequencing of 16S rRNA genes (V4 region). A series of three studies examined: 1) the effect of nanocrystalline versus microcrystalline cellulose; 2) the effects of nanocellulose morphology (crystalline rod versus filament) and surface functionalization (cationic and anionic); and 3) metagenomic characterization of cellulose degrading communities using next-generation DNA sequencing. It was found that the nano- size range did not hinder cellulose degradation, in fact, nanocrystalline cellulose degraded slightly faster than microcrystalline cellulose according to 1st order kinetics (1st order decay constants: 0.62±0.08 wk-1 for anionic nanocrystalline cellulose versus 0.39±0.05 wk-1 for microcrystalline cellulose exposed to AD culture; 0.69±0.04 wk-1 for anionic nanocrystalline cellulose versus 0.58±0.05 wk-1 for microcrystalline cellulose exposed to W). Experiments comparing the effects of surface functionalization indicated that anionic nanocellulose degraded faster than cationic cellulose (1st order decay constants for cationic nanocrystalline cellulose: 0.48±0.06 wk-1 and 0.58±0.07 wk-1 on exposure to AD and W cultures respectively). Measurements of 16S rRNA and cel48 genes were consistent with this trend of greater biological growth and cellulose-degrading potential in the anionic nanocellulose condition, suggesting that surface properties can influence biodegradation patterns. Taxonomic characterization of 16S rRNA gene amplicons suggested that taxa known to contain anaerobic cellulose degraders were enriched in both W and AD consortia, which shifted in a distinct manner in response to exposure to the different cellulosic materials. This suggests that distinct groups of microbes may drive the biodegradation of different forms of cellulose. Further, metagenomic investigation provided new insight into taxonomic and functional aspects of anaerobic cellulose degradation, including identification of enzymatic families associated with degradation of the various forms of cellulose. Overall, the findings of this study advance understanding of anaerobic cellulose degradation and indicate that nanocellulose is likely to readily degrade in receiving environments and not pose an environmental concern.
Electrospun Nanocellulose: A New Biomaterial
Rodriguez Rivera, Katia Argelia (Virginia Tech, 2011-09-23)
Science and engineering studies on biocompatible implantable materials for tissue and organ repair have recently focused on polymeric materials to serve as scaffolds for cellular integration. Cellulose in many forms has been demonstrated as potential biopolymer for tissue engineering; however, it has not been previously electrospun into a scaffold for tissue engineering applications. The overall goal of this research project was to produce electrospun cellulose acetate (CA) nanofibers with specific architectures and surface chemistries to be evaluated as scaffolds for tissue regeneration. The size and morphology of electrospun CA was impacted by polymer concentration, solvent system, and solution flow rate. The conversion of CA electrospun scaffolds into regenerated cellulose by exposure to NaOH ethanol solution was successful for scaffolds produced at polymer solution flow rate of at least 1 mL/h. The regeneration process resulted in minimal degradation of the cellulose while retaining the original fiber structure of the scaffold. In vitro cytotoxicity evaluation of the fibrous cellulose scaffolds on a culture of mouse fibroblast (L-929) cells indicated that this material posed no threat to mammalian cells. Electrospun cellulose scaffolds with different architectures and surface chemistries were designed and evaluated to enhance scaffold properties and cell adhesion. The morphology of the partially regenerated cellulose revealed only a broad diffraction peak for the scaffold material, while the fully regenerated cellulose showed a characteristic semi-crystalline cellulose II diffraction pattern. Fiber orientation and porosity of the scaffolds were controlled by electrospining CA solution onto the edge of a rotator wheel and laser microablation, respectively. Bioactivity of the scaffolds was shown to be enhanced via scaffold surface modification with either anionic or cationic functional groups. Biomimetic Ca-P crystal mineralization on electrospun cellulose fibers was produced by means of carboxymethyl cellulose (CMC) adsorption and treatments with simulated body fluid (SBF) or phosphate buffer saline (PBS) solutions. Porosity and Ca-P crystals enhanced osteoprogenitor cell adhesion on the electrospun cellulose scaffolds. Cationic modification by trimethyl ammonium betahydroxy propyl (THAMP) derivation and adsorption of extracellular matrix proteins on cellulose fibers promoted adhesion and proliferation of neural-like (PC12) and myoblast (C2C12) cells. Differentiation of myoblast cells (C2C12) towards myotubes on electrospun cellulose scaffolds was controlled by surface chemistry and mechanical properties. Together these studies showed great potential for cellulose acetate to be electrospun and converted into a viable biocompatible tissue engineering scaffolds.
Improved Properties of Poly (Lactic Acid) with Incorporation of Carbon Hybrid Nanostructure
Kim, Junseok (Virginia Tech, 2016-07-01)
Poly(lactic acid) is biodegradable polymer derived from renewable resources and non-toxic, which has become most interested polymer to substitute petroleum-based polymer. However, it has low glass transition temperature and poor gas barrier properties to restrict the application on hot contents packaging and long-term food packaging. The objectives of this research are: (a) to reduce coagulation of graphene oxide/single-walled carbon nanotube (GOCNT) nanocomposite in poly(lactic acid) matrix and (b) to improve mechanical strength and oxygen barrier property, which extend the application of poly(lactic acid). Graphene oxide has been found to have relatively even dispersion in poly(lactic acid) matrix while its own coagulation has become significant draw back for properties of nanocomposite such as gas barrier, mechanical properties and thermo stability as well as crystallinity. Here, single-walled carbon nanotube was hybrid with graphene oxide to reduce irreversible coagulation by preventing van der Waals of graphene oxide. Mass ratio of graphene oxide and carbon nanotube was determined as 3:1 at presenting greatest performance of preventing coagulation. Four different weight percentage of GOCNT nanocomposite, which are 0.05, 0.2, 0.3 and 0.4 weight percent, were composited with poly(lactic acid) by solution blending method. FESEM morphology determined minor coagulation of GOCNT nanocomopsite for different weight percentage composites. Insignificant crystallinity change was observed in DSC and XRD data. At 0.4 weight percent, it prevented most of UV-B light but was least transparent. GOCNT nanocomposite weight percent was linearly related to ultimate tensile strength of nanocomposite film. The greatest ultimate tensile strength was found at 0.4 weight percent which is 175% stronger than neat poly(lactic acid) film. Oxygen barrier property was improved as GOCNT weight percent increased. 66.57% of oxygen transmission rate was reduced at 0.4 weight percent compared to neat poly(lactic acid). The enhanced oxygen barrier property was ascribed to the outstanding impermeability of hybrid structure GOCNT as well as the strong interfacial adhesion of GOCNT and poly(lactic acid) rather than change of crystallinity. Such a small amount of GOCNT nanocomposite improved mechanical strength and oxygen barrier property while there were no significant change of crystallinity and thermal behavior found.
Investigating Differences in Douglas-fir and Southern Yellow Pine Bonding Properties
Mirabile, Kyle Vincent (Virginia Tech, 2015-10-22)
Differences in southern yellow pine (represented by Pinus taeda) and Douglas-fir (Pseudotsuga menziesii) mature and juvenile wood were examined in terms of density, chemical composition, surface energy, shear stress, % wood failure, and delamination. Density was measured using a QTRS density scanner. Loblolly pine contained a higher average density. Chemical composition was measured using the NREL standard for identifying the chemical composition of biomass. Southern yellow pine contained a higher % hemicellulose, lignin, and extractives. Douglas-fir had higher % cellulose than southern yellow pine. Surface energy was measured using the static sessile drop contact angle method and the acid/base approach. Southern yellow pine contained a lower average contact angle than Douglas-fir. Shear stress, % wood failure, and durability were measured using ASTM-D2559 with two adhesives, a one-part moisture cure polyurethane (PU), and a two-part ambient curing phenol-resorcinol-formaldehyde (PRF). Shear stress for southern yellow pine was affected the most by the type of growth regions at the bond (juvenile to mature wood) and the assembly times of the adhesives used. Douglas-fir shear stress was affected by the type of adhesive and the growth region at the bond. Delamination results demonstrated that when using PRF the southern yellow pine has less delamination statistically than Douglas-fir. Also, the growth region at the bond with both adhesives showed to impact delamination with juvenile to mature wood having less delamination than mature to mature wood.
Laser Activated Bonding of Wood
Church, William Travis (Virginia Tech, 2010-11-11)
It was found that laser modified wood surfaces can be bonded together to create a wood composite without the need of any additive. This bonding method removes the need of applying adhesive, potentially lowers cost, and eliminates off gassing of petroleum resins, creating a wood product with many eco-friendly attributes. This body of work outlines a) initial chemical analysis of the laser modified surface b) its bond strength and c) the optimization of factors that control the strength of the bond. Surface chemical analysis on laser modified wood was conducted using photo acoustic Fourier transform infrared spectroscopy (PA-FTIR) and X-Ray photoelectron spectroscopy (XPS). Light microscopy and scanning electron microscopy were utilized for surface topology analysis.Differential scanning calorimetry (DSC) quantified the thermal properties of the modified wood surface. Screening of multiple factors that would contribute to surface modification and adhesion was performed utilizing mechanical testing. Optimization of significant factors that affect bond strength was determined statistically utilizing a design of experiment approach. Chemical analysis of the laser modified surface revealed changes in the carbonyl and aromatic regions indicating modification of the hemicellulose and lignin components, intensifying with increasing laser modification.The C1/C2 ratios found via XPS revealed that one or more of the following is occurring: more extractives have moved to the surface, condensation reactions among lignin units, and the loss of methoxy and breakage of aryl ether linkages occurred.Microscopy images showed color changes to a darker caramel color with a smoothing of surface topology, suggesting the occurrence of the softening and/or melting of wood polymers. DSC verified chemical and/or physical changes in the wood with the modified material now having a glass transition temperature between 130-150°C.DOE found that laser parameters (power and focus) as well as hot press parameters (temperature and pressure) were significant in optimizing the bond. The impact of the study is the first documentation of the ability to laser modifies wood surfaces and subsequently bond them together. The ability of the wood polymers at the surface to undergo flow at elevated temperature is implicated in the adhesion mechanism of the laser modified wood.
Lignocellulose deconstruction using glyceline and a chelator-mediated Fenton system
Orejuela, Lourdes Magdalena (Virginia Tech, 2017-12-15)
Non-edible plant biomass (lignocellulose) is a valuable precursor for liquid biofuels, through the processes of pretreatment and saccharification followed by fermentation into products such as ethanol or butanol. However, it is difficult to gain access to the fermentable sugars in lignocellulose, and this problem is principally associated with limited enzyme accessibility. Hence, biomass pretreatments that destroy native cell wall structure and allows enzyme access are required for effective biomass conversion techniques. This research studied two novel pretreatment methods on two wood species: 1) a deep eutectic solvent (DES) that, under heat, swells lignocellulose and partially solubilizes cell wall materials by causing breakage of lignin-carbohydrate linkages and depolymerization of the biomass components, and 2) a chelator-mediated Fenton reaction (CMF) that chemically modifies the nanostructure of the cell wall through a non-enzymatic cell wall deconstruction. After pretreatment, utilizing analytical techniques such as nuclear magnetic spectroscopy, wide angle x-ray scattering, and gel permeation chromatography, samples were analyzed for chemical and structural changes in the solubilized and residual materials. After single stage DES (choline-chloride-glycerol) and two stage, CMF followed by DES pretreatments, lignin/carbohydrate fractions were recovered, leaving a cellulose-rich fraction with reduced lignin and hemicellulose content as determined by compositional analysis. Lignin and heteropolysaccharide removal by DES was quantified and the aromatic-rich solubilized biopolymer fragments were analyzed as water insoluble high molecular weight fractions and water-ethanol soluble low molecular weight compounds. After pretreatment for the hardwood sample, enzyme digestibility reached a saccharification yield of 78% (a 13-fold increase) for the two stage (DES/CMF) pretreated biomass even with the presence of some lignin and xylan remained on the pretreated fiber; only a 9-fold increase was observed after the other sequence of CMF followed by DES treatment. Single stage CMF treatment or single stage DES pretreatment improved 5-fold glucose yield compared to the untreated sample for the hardwood sample. The enhancement of enzymatic saccharification for softwood was less than that of hardwoods with only 4-fold increase for the sequence CMF followed by DES treatment. The other sequence of treatments reached up to 2.5-fold improvement. A similar result was determined for the single stage CMF treatment while the single stage DES treatment reached only 1.4-fold increase compared to the untreated softwood. Hence, all these pretreatments presented different degrees of biopolymer removal from the cell wall and subsequent digestibility levels; synergistic effects were observed for hardwood particularly in the sequence DES followed by CMF treatment while softwoods remained relatively recalcitrant. Overall, these studies revealed insight into two novel methods to enhance lignocellulosic digestibility of biomass adding to the methodology to deconstruct cell walls for fermentable sugars.
Mechanisms of biogenic formaldehyde generation in wood
Wan, Guigui (Virginia Tech, 2017-02-10)
This work addresses biogenic formaldehyde (CH₂O) generated by wood during the manufacture of non-structural wood-based composites, from which CH₂O emissions are regulated. The target for regulation has been anthropogenic CH₂O released from hydrolytically unstable amino resins like urea-formaldehyde. However, current regulations (the Formaldehyde Standards for Composite Wood Products Act, signed into law in 2010 and implemented in 2016) restrict allowable emissions to such low levels that biogenic CH₂O may affect regulation compliance. The industry has met the latest regulations with new amino resin technologies. Nevertheless persistent anecdotal reports suggest that biogenic CH₂O complicates regulation compliance. This work represents an industry/university cooperation to seek a more thorough understanding of biogenic CH₂O, to begin documentation of biogenic CH₂O levels in wood, and to study the conditions and chemical mechanisms of its formation. Efforts began by establishing CH₂O analysis using the fluorimetric acetylacetone determination. A custom 12-liter chamber with controlled temperature and relative humidity, and "ultrapure" nitrogen (N₂) ventilation was created to measure CH₂O emissions from flakes sampled from four Virginia pine (Pinus virginiana) trees. Emissions from never-heated specimens varied significantly among the four trees, ranging from 0.02 – 0.19 µg CH₂O/m³g dry wood. Heating (200°C, 1 hour), followed by chamber equilibration, resulted in significantly increased emissions on the order of 50%. Sequential heating, followed by chamber equilibration (in other words, heat/equilibrate/measure emission/repeat), resulted in declining emissions suggesting that a finite chemical source of CH₂O was being depleted by the sequential heat treatment. Flake specimens were stored in the open laboratory, and over 2-3 months laboratory storage, initially high emitting specimens gradually emitted less CH₂O, and initially low emitters gradually emitted more CH₂O. Concerns over laboratory contamination were perhaps allayed when background levels of laboratory CH₂O were determined to be similar to the background levels in the ultrapure N₂ used to ventilate the chamber. Measurement of emissions was abandoned, and thereafter a simple water extraction technique (~ 94% CH₂O recovery) was used to measure the CH₂O content of never-heated and heated wood specimens, where the difference was identified as CH₂O generated due to heating. Increment cores from living Virginia pine (Pinus virginiana), yellow-poplar (Liriodendron tulipifera), and radiata pine (Pinus radiata) trees were used to measure CH₂O content and CH₂O generation due to heating (200°C, 10 min). Significant variations within and between trees of the same species were observed. Tissue types (juvenile/mature, heartwood/sapwood) sometimes correlated to higher CH₂O contents and greater heat-generation potential; but sometimes not depending upon species. Heating increased CH₂O levels 3-60 fold. Heating with high moisture levels caused greater CH₂O generation than for dry specimens. This moisture effect and a separate serendipitous observation suggested that CH₂O generation is acid catalyzed. Radiata pine generated extraordinarily high CH₂O levels when heated, far exceeding the other two species. It was suggested that pine extractives might catalyze CH₂O generation, perhaps in lignin. Pinus virginiana wood was heated (200°C, 10 or 60 min) while dry or after aqueous/acid or base pretreatment in order to reveal mechanisms of formaldehyde (CH₂O) generation. Among wood structural polymers, lignin was the overwhelming source of biogenic CH₂O, consistent with prior reports. The effects of wood extractives are mentioned below. The selection of acid catalyst strongly affected CH₂O generation as predicted in the acidolysis literature of lignin model compounds and isolated lignins. Lignin methoxyl cleavage was also observed, but was considered an unlikely source of thermochemical CH₂O. Alkaline pretreatments suppressed CH₂O generation. Regarding wood-based composite manufacture, the implications are that lignin reactions can be manipulated during hot-pressing. Potential benefits include reduced product emissions, and/or novel crosslinking strategies using biogenic CH₂O. Heat generation of CH₂O in Virginia pine and radiata pine was substantially reduced by extractives removal, but there was no such effect in yellow-poplar wood. Results suggested that pine extractives promote CH₂O generation by catalyzing or otherwise promoting C2 cleavage (acidolysis) in lignin. Thioacidolysis demonstrated that pine lignin reactions were strongly dependent upon the presence or absence of the extractives. When present, pine extractives seemed to promote C2 cleavage (CH₂O generation), but otherwise reduced the overall extent of lignin degradation. When pine extractives were removed, lignin suffered substantial degradation, but apparently less C2 cleavage since CH₂O generation was reduced. In contrast, thioacidolysis showed that yellow-poplar extractives appeared to promote lignin degradation, but extractives removal had no detectable impact on CH₂O generation. Implications exist for biorefinery research because it was shown that lignin reactions can be strongly affected by wood extractives. Two dimensional, proton-carbon, correlation NMR spectroscopy (2D NMR), and solvent submersion dynamic mechanical analysis (DMA) was used to investigate wood changes caused by heating in the presence or absence of external acid catalysis. 2D NMR was relatively insensitive to fine lignin changes that were detected using thioacidolysis. 2D NMR was effective for observing lignin changes under more extreme heating conditions, and evidence was found for lignin crosslinking reactions that probably occurred through substitution into lignin aromatic rings. DMA showed that most heating conditions caused an increase in the lignin glass transition temperature (Tg), consistent with heat-induced lignin crosslinking. Under one experimental condition of wood heating, DMA showed a reduction in the lignin glass transition temperature (Tg). This suggested that lignin cleavage without subsequent repolymerization might be promoted by carefully controlled conditions, and this has implications for biorefinery research where lignin repolymerization can be problematic. Finally, this work strongly supported the hypothesis that lignin generates CH₂O through well-known acidolysis pathways where CH₂O is borne from the lignin gamma-methylol group. Therefore, it was predicted that upon heating corn (Zea mays L.) stalk should generate less CH₂O than wood because corn stalk lignins exhibit a high degree of coumaric acid esterfication at the gamma-methylol group. This hypothesis was perhaps verified- it was found that in 4 out of 6 experimental heating conditions that corn stalk generated significantly less CH₂O than Virginia pine.
Modification of Wood Fiber with Thermoplastics by Reactive Steam-Explosion
Renneckar, Scott Harold (Virginia Tech, 2004-07-16)
For the first time, a novel processing method of co-refining wood and polyolefin (PO) by steam-explosion was scientifically explored for wood-thermoplastic composites without a coupling agent. Traditional studies have addressed the improvement of adhesion between components of wood thermoplastic composites through the use of coupling agents such as maleated PO. The objective of this study was to increase adhesion between wood and PO through reactive processing conditions of steam-explosion. PO characteristics, such as type (polyethylene or polypropylene), form (pellet, fiber, or powder) and melt viscosity were studied along with oxygen gas content of the steam-explosion reactor vessel. Modification of co-processed wood fiber was characterized in four studies: microscopy analysis of dispersion of PO with wood fiber, sorption properties of co-processed material, chemical analysis of fractionated components, and morphological investigation of co-processed material. Two additional studies are listed in the appendices that relate to adsorption of amphiphilic polymers to the cellulose fiber surface, which is one hypothesis of fiber surface modification by co-steam-explosion. Microscopy studies revealed that PO melt viscosity was found to influence the degree of dispersion and uniformity of the steam-exploded material. The hygroscopic nature of the co-processed fiber declined as shown by sorption isotherm data. Furthermore, a water vapor kinetics study found that all co-refined material had increased initial diffusion coefficients compared to the control fiber. Chemical changes in fractionated components were PO-type dependent. Lignin extracted from co-processed wood and polyethylene showed PO enrichment determined from an increase of methylene stretching in the Fourier Transform infrared subtraction spectra, while lignin from co-processed wood and polypropylene did not. Additionally, extracted PO showed indirect signs of oxidation as reflected by fluorescence studies. Solid state nuclear magnetic resonance spectroscopy revealed a number of differences in the co-processed materials such as increased cellulose crystallinity, new covalent linkages and an alternative distribution of components on the nanoscale reflected in the T1Ï relaxation parameter. Steam-explosion was shown to modify wood fiber through the addition of "non-reactive" polyolefins without the need for coupling agents. In light of these findings, co-refining by steam-explosion should be viewed as a new reactive processing method for wood thermoplastic composites.
Nanocellulose: Preparation, Characterization, Supramolecular Modeling, and its Life Cycle Assessment
Li, Qing Qing (Virginia Tech, 2012-12-13)
Nanocellulose is a nascent and promising material with many exceptional properties and a broad spectrum of potential applications; hence, it has drawn increasing research interests in the past decade. A new type of nanocellulose -- with mono- or bi-layer cellulose molecular sheet thickness -- was synthesized through a combined chemical-mechanical process (TEMPO-mediated oxidation followed by intensive sonication), and this new material was named molecularly thin nanocellulose (MT nanocellulose). The overarching objective of this study was to understand the formation and supramolecular structure of MT nanocellulose and contribute to the knowledge of native cellulose structure. The research involved four major bodies of study: preparation of MT nanocellulose, characterization of MT nanocellulose, modeling wood pulp-derived cellulose microfibril cross section structure, and a comparative life cycle assessment (LCA) of different nanocellulose fabrication approaches. The results revealed that MT nanocellulose with mono- to bi-layer sheet thickness (~0.4-0.8 nm), three to six chain width (~2-5 nm), and hundreds of nanometers to several microns length, can be prepared through TEMPO-mediated oxidation followed by 5-240 min intensive sonication. The thickness, width, and length of MT nanocellulose all decreased with extended sonication time and leveled off after 1 or 2 h sonication. Crystallinity, hydrogen bonding, and glycosidic torsion angles were evaluated by XRD, FTIR, Raman, and NMR. These experiments revealed systematic changes to structure with sonication treatments. A microfibril "cross section triangle scheme" was developed for the microfibril supramolecular modeling process and a 24-chain hexagonal/elliptical hybrid model was proposed as the most credible representation of the supramolecular arrangement for wood pulp-derived cellulose I" microfibril. Comparative LCA of the fabrication of nanocellulose indicated that nanocellulose presented a significant environmental burden markup on its precursor, kraft pulp, and the environmental hotspot was attributed to the mechanical disintegration process. Yet, overall nanocellulose still presented a prominent environmental advantage over other nanomaterials like single-walled carbon nanotubes, due to its relative low energy consumption. Overall, this research developed a facile approach to produce a new type of nanocellulose, the MT nanocellulose, provided new insights about the supramolecular structure of cellulose microfibrils, and evaluated the environmental aspects of the fabrication process of nanocellulose.
Nanocomposite-based Lignocellulosic Fibers
Lin, Zhiyuan (Virginia Tech, 2009-12-16)
The formation of layered nanoparticle films on the surface of wood fibers is reported in this study. The layer-by-layer (LbL) assembly technique was comprehensively investigated as a non-covalent surface modification method for lignocellulosic fiber. Nanocomposite-based lignocellulosic fibers were successfully fabricated by sequential adsorption of oppositely charged poly(diallydimethylammonium) chloride (PDDA) and clay nanoparticles in a number of repeated deposition cycles. Nanocomposite fibers displayed layered structure as indicated by the electrokinetic potential studies and scanning electron microscopy (SEM) analysis. Layer-by-layer films of PDDA and clay impacted the thermal stability of wood fibers. Average degradation temperature at 5 and 10% weight loss for modified fibers with 4 bi-layers increased by up to ~24 and ~15°C, respectively. Significant char residue formed for the LbL modified fibers after heating to 800°C, indicating that the clay-based coating may serve as a barrier, creating an insulating layer to prevent further decomposition of the material. Layer-by-layer film formation on wood fibers was investigated as a function of parameters related to fiber composition and solution conditions (ie. presence of lignin, salt concentration and pH). Elemental analysis of modified fibers revealed that PDDA adsorption to the fibers was reduced for all solution conditions for the samples with the highest content of lignin. Upon extracting the non-covalently attached lignin, the samples showed the greatest amount of PDDA adsorption, reaching to 1.5% of total mass, under neutral solution conditions without the presence of added electrolyte. Furthermore, the influence of both the amount of PDDA adsorbed onto the fiber surface and electrokinetic potential of modified fibers on subsequent multilayer formation was quantified. Under select fiber treatments, great amount of PDDA/clay (up to ~75% total mass for only 4 bi-layers) was adsorbed onto wood fibers through the LbL process, giving these high surface area fibers nanocomposite coatings. LbL modified fibers were melt compounded with isotactic polypropylene (PP) and compression molded into test specimens. The effect of LbL modification as a function of the number of bi-layers on composite performance was tested using the tensile, flexural, dynamic mechanical and thermal properties of fiber reinforced thermoplastic composites. LbL modified fiber composites had similar modulus values but significantly lower strength values than those of unmodified fiber composites. However, composites composed of LbL modified fibers displayed increased elongation at break, increasing by more than 50%, to those of unmodified samples. DSC results indicated that crystallization behavior of PP is promoted in the presence of wood fibers. Both unmodified and LbL modified fibers are able to acts as nucleating agents, which cause an increase of the crystallinity of PP. Moreover, results from tensile and flexural strength, dynamic mechanical analysis and water absorption tests revealed that the material (PDDA or clay) at the terminal (outer) layer of LbL modified fiber influences the performance of the composites. These findings demonstrate control over the deposition of nanoparticles onto lignocellulosic fibers influencing terminal surface chemistry of the fiber. Further investigation into using renewable fibers as carriers of nanoparticle films to improve fiber durability, compounding with thermoplastics that have higher melt processing temperatures, and tailoring terminal surface chemistry to enhance adhesion is justified by this research.
Nanoscale surface modification of wood veneers for adhesion
Zhou, Yu (Virginia Tech, 2008-09-01)
Surface chemistry of wood is based on the exposed cut surface that is the combination of intact (lumen wall) and cut cell wall material. It is inherently complex and changes with history of processing. Modification of wood surface through noncovalent attachment of amine containing water soluble polyelectrolytes provides a path to create functional surfaces in a controlled manner. Furthermore, modification of the surface can be performed using layer-by-layer (LbL) assembly, where the adsorption of polyelectrolytes or nanoparticles in sequential steps yields a multilayer film with a defined layer sequence on a given substrate. The objective of this study was to quantify adsorption of polyelectrolytes onto wood surface and use these polyelectrolytes as adhesives. In this study, optimal pH conditions for modifying wood surfaces, by anchoring adsorbing polyelectrolytes, were detected using zeta- ( )-potential measurements. Positively charged wood surfaces were also detected by the same technique after a layer of poly(diallyldimethylammonium chloride) (PDDA) or poly (ethylenimine) (PEI) was adsorbed. Both X-ray photoelectron spectroscopy (XPS) and Carbon-Nitrogen-Sulfur analyzer (CNS) were used to quantify the amount of charged polymer on wood surfaces to elucidate optimal pH and ionic strength for polyelectrolyte adsorption. Confocal laser scanning microscopy (CLSM) and Environmental Scanning Electron Microscope (ESEM) were used to characterize adsorbed LbL multilayers of poly(acrylic) acid (PAA) and poly(allylamine hydrochloride) (PAH). Cross-linking between PAA and PAH at various temperatures was studied by Fourier Transform Infrared Spectroscopy (FTIR) and the evaluation of multilayer as bonding agents was carried out by compression shear test following ASTM D905 standard.
Novel Liquid extraction method for detecting Native-wood Formaldehyde
Tasooji, Mohammad (Virginia Tech, 2014-06-06)
New vigorous regulations have been established for decreasing the allowable formaldehyde emissions from nonstructural wood based composites. Two main sources of formaldehyde emission in non-structural wood based composites are adhesive and wood. Adhesives are quite well known and great efforts have been conducted to decrease their formaldehyde content; however formaldehyde emission from wood has received little attention and it is not completely understood. Wood-borne formaldehyde emission exists in a complex equilibrium in wood matrix. The reaction between formaldehyde and wood hydroxyl groups/water can hinder the complete formaldehyde extraction. In order to have a complete formaldehyde extraction, a stronger nucleophile than hydroxyl and water groups is needed. In this study cross-linked poly (allylamine) (PAA) beads were synthesized and used as a strong nucleophile to extract all the biogenic and synthetic free-formaldehyde within the woody matrix of never-heated and heat-treated Virginia pines; the results were compared to simple water extraction. A new formaldehyde capturing device was also developed using a serum bottle. Results showed that there was no advantage of using PAA beads over simple water extraction for extracting woody matrix free-formaldehyde. This means that simple water extraction can extract all the free-formaldehyde from the woody matrix. It was also found that thermal treatment resulted in generating more wood-borne formaldehyde. The other important finding was the new developed formaldehyde capturing device. The device was very promising for detecting wood-borne formaldehyde from very small pieces of wood (5-70 mg) and can be very useful in future studies.
Organic Fillers in Phenol-Formaldehyde Wood Adhesives
Yang, Xing (Virginia Tech, 2014-10-10)
Veneer-based structural wood composites are typically manufactured using phenol-formaldehyde resols (PF) that are formulated with wheat flour extender and organic filler. Considering that this technology is several decades old, it is surprising to learn that many aspects of the formulation have not been the subject of detailed analysis and scientific publication. The effort described here is part of a university/industry research cooperation with a focus on how the organic fillers impact the properties of the formulated adhesives and adhesive bond performance. The fillers studied in this work are derived from walnut shell (Juglans regia), alder bark (Alnus rubra), and corn cob (furfural production) residue. Alder bark and walnut shell exhibited chemical compositions that are typical for lignocellulosic materials, whereas corn cob residue was distinctly different owing to the high pressure steam digestion used in its preparation. Also, all fillers had low surface energies with dominant dispersive effects. Surface energy of corn cob residue was a little higher than alder bark and walnut shell, which were very similar. All fillers reduced PF surface tension with effects greatest in alder bark and walnut shell. Surface tension reductions roughly correlated to the chemical compositions of the fillers, and probably resulted from the release of surface active compounds extracted from the fillers in the alkaline PF medium. It was shown that viscoelastic network structures formed within the adhesive formulations as a function of shear history, filler type, and filler particle size. Relative to alder bark and walnut shell, the unique behavior of corn cob residue was discussed with respect to chemical composition. Alder bark and walnut shell exhibited similar effects with a decrease of adhesive activation energy. However, corn cob reside caused much higher adhesive activation energy. Alder bark exhibited significant particle size effects on fracture energy and bondline thickness, but no clear size effects on penetration. Regarding corn cob residue and walnut shell, particle size effects on fracture energy were statistically significant, but magnitude of the difference was rather small. Classified corn cob residue fillers all resulted in a similar bondline thickness (statistically no difference) that was different walnut shell.
Self-Assembly of Large Amyloid Fibers
Ridgley, Devin Michael (Virginia Tech, 2014-05-29)
Functional amyloids found throughout nature have demonstrated that amyloid fibers are potential industrial biomaterials. This work introduces a new 'template plus adder' cooperative mechanism for the spontaneous self-assembly of micrometer sized amyloid fibers. A short hydrophobic template peptide induces a conformation change within a highly α-helical adder protein to form β-sheets that continue to assemble into micrometer sized amyloid fibers. This study utilizes a variety of proteins that have template or adder characteristics which suggests that this mechanism may be employed throughout nature. Depending on the amino acid composition of the proteins used the mixtures form amyloid fibers of a cylindrical (~10 μm diameter, ~2 GPa Young's modulus) or tape (5-10 μm height, 10-20 μm width and 100-200 MPa Young's modulus) morphology. Processing conditions are altered to manipulate the morphology and structural characteristics of the fibers. Spectroscopy is utilized to identify certain amino acid groups that contribute to the self-assembly process. Aliphatic amino acids (A, I, V and L) are responsible for initiating conformation change of the adder proteins to assemble into amyloid tapes. Additional polyglutamine segments (Q-blocks) within the protein mixtures will form Q hydrogen bonds to reinforce the amyloid structure and form a cylindrical fiber of higher modulus. Atomic force microscopy is utilized to delineate the self-assembly of amyloid tapes and cylindrical fibers from protofibrils (15-30 nm width) to fibers (10-20 μm width) spanning three orders of magnitude. The aliphatic amino acid content of the adder proteins' α-helices is a good predictor of high density β-sheet formation within the protein mixture. Thus, it is possible to predict the propensity of a protein to undergo conformation change into amyloid structures. Finally, Escherichia coli is genetically engineered to express a template protein which self-assembles into large amyloid fibers when combined with extracellular myoglobin, an adder protein. The goal of this thesis is to produce, manipulate and characterize the self-assembly of large amyloid fibers for their potential industrial biomaterial applications. The techniques used throughout this study outline various methods to design and engineer amyloid fibers of a tailored modulus and morphology. Furthermore, the mechanisms described here may offer some insight into naturally occurring amyloid forming systems.
Structural Determination of Copolymers from the Cross-catalyzed Reactions of Phenol-formaldehyde and Polymeric Methylenediphenyl Diisocyanate
Haupt, Robert A. (Virginia Tech, 2013-05-07)
This work reports the elucidation of the structure of a copolymer generated by the cross- catalyzed reactions of PF and pMDI prepolymers. The electronic behavior of phenolic monomers as perturbed by alkali metal hydroxides in an aqueous environment was studied with 1H and 13C NMR. Changes in electronic structure and thus reactivity were related to solvated ionic radius, solvent dielectric constant, and their effect on ion generated electric field strength. NMR chemical shifts were used to predict order of reactivity for phenolic model compounds with phenyl isocyanate with good success. As predicted, 2-HMP hydroxymethyl groups were more reactive than 4-HMP in forming urethane bonds under neutral conditions and 2-HMP hydroxymethyl groups were more reactive than 4-HMP in forming urethane bonds under alkaline conditions. The structure of the reaction products of phenol, benzyl alcohol, 2-HMP, and 4-HMP with phenyl isocyanate were studied using 1H and 13C NMR under neutral organic and aqueous alkaline conditions. Reactions in THF-d8 under neutral conditions, without catalyst, were relatively slow, resulting in residual monomer and the precipitation of 1,3-diphenyl urea from the carbamic acid reaction. The reactions of phenol, 2-HMP, and 4-HMP in the presence of TEA catalyst favored the formation of phenyl urethanes (PU). Reactions with benzyl alcohol, 2-HMP, and 4-HMP in the presence of DBTL catalyst favored the formation of benzyl urethanes (BU). Reactions of 2-HMP and 4-HMP led to formation of benzylphenyldiurethane (BPDU). DBTL catalysts favored formation of BDPU strictly by a benzyl urethane pathway, while TEA favored its formation mostly via phenyl urethane, although some BU was also present. Under aqueous alkaline conditions, 2-HMP was more reactive than 4-HMP, exhibiting an enhanced reactivity that was attributed to intramolecular hydrogen bonding and a resulting resonance stabilization of the phenolic aromatic ring. ATR-FTIR spectroscopic studies generated real time structural information for model compound reactions of the cross-catalyzed system, differentiating among reaction peaks generated by the carbamic acid reaction, PU and BU formation. ATR-FTIR also permitted monitoring of propylene carbonate hydrolysis and accelerated alkaline PF resole condensation. ATR-FTIR data also showed that the overall reaction stoichiometry between the PF and pMDI components drove copolymer formation. Benzyl urethane formation predominated under balanced stoichiometric conditions in the presence of ammonium hydroxide, while phenyl urethane formation was favored in its absence. Accelerated phenolic methylene bridge formation became more important when the PF component was in excess in the presence of sufficient accelerator. A high percentage of free isocyanate was present in solid copolymer formed at ambient temperature. The combination of ammonium hydroxide and tin (II) chloride synergistically enhanced the reactivity of the materials, reducing the residual isocyanate. From 13C CP/MAS NMR of the copolymer, the presence of ammonium hydroxide and tin (II) chloride and the higher PF concentration resulted in substantial urethane formation. Ammonium hydroxide favored formation of benzyl urethane from the 2-hydroxymethyl groups, while phenyl urethane formed in its absence. The low alkalinity PF resole with ammonium hydroxide favored benzyl urethane formation. Comparison of these results with the 13C NMR model compound reactions with phenyl isocyanate under alkaline conditions confirmed high and low alkalinity should favor phenyl and benzyl urethane formation respectively. These cross catalyzed systems are tunable by formulation for type of co-polymer linkages, reactivity, and cost.

Browsing by Author "Renneckar, Scott Harold"

Results Per Page

Sort Options