Browsing by Author "Roman, Maren"

Now showing 1 - 20 of 66
  • Thumbnail Image
    Adhesion Fundamentals in Spotted Gum (Corymbia citriodora)
    Burch, Coleman Patrick (Virginia Tech, 2015-12-23)
    The goal of this project was to advance adhesion science and technology related to the Australian hardwood spotted gum (Corymbia citriodora). Plantation-grown spotted gum exhibits poor adhesion properties in comparison with similar woods, such as Gympie messmate (Eucalyptus cloeziana). To better understand adhesion differences between these two woods, this research compared and contrasted the surface chemistries of plantation-grown spotted gum and Gympie messmate with a particular focus on sensitivity to thermal deactivation. Wetting measurements were performed using the sessile drop method. Initial and equilibrium contact angles, time-dependent wetting, and surface energy were determined. Time-dependent wetting and equilibrium contact angles were most informative. Initial contact angles and surface energy calculated with them were misleading and often generated anomalous results. Heating water-saturated wood to mild surface temperatures (105 deg C, directly after evaporative cooling) severely deactivated spotted gum but not Gympie messmate. This suggests conventional kiln drying appears unsuitable for spotted gum while amenable for Gympie messmate. Spotted gum likely requires non-aqueous, low surface tension adhesives or aqueous adhesives formulated with surface active wetting agents. Water-saturation (followed by room-temperature vacuum drying) substantially altered the surface chemistries of both woods, making them more hydrophilic. Consequently, the question was raised of whether a water-spray onto the wood surface prior to adhesive application could improve bonding. If so, this simple, industrially-feasible treatment could prove very beneficial to the wood composites industry. Water-saturation also revealed differences in the two wood's water permeability, which has implications for adhesive penetration and wood drying and may additionally help explain adhesion differences. Analysis of the plantation-grown heartwood (inner, middle, and outer heartwood regions) revealed significant wetting differences on spotted gum with only minor differences on Gympie messmate. The Australian woods were compared to two North American woods-loblolly pine (Pinus taeda) and Douglas-fir (Pseudotsuga menziesii). Examining water wetting measurements, the Australian and North American woods exhibited some interesting similarities. However, methylene iodide wetting measurements revealed that the Australian woods were quite different from the North American samples studied here.
  • Thumbnail Image
    Adsorption of Biomacromolecules onto Polysaccharide Surfaces
    Zhang, Xiao (Virginia Tech, 2014-10-02)
    Plant cell wall polysaccharides are abundant natural polymers making them potential sources for sustainable and biodegradable materials. Interfacial behavior, including adsorption and enzymatic degradation, of several plant cell wall polysaccharides and their derivatives were studied with a quartz crystal microbalance with dissipation monitoring (QCM-D), surface plasmon resonance (SPR) and atomic force microscopy (AFM). Xyloglucan adsorption isotherms were obtained to probe how cellulose-hemicellulose interactions were affected by the type of cellulose substrate and molar mass of xyloglucan. Xyloglucan as small as a heptasaccharide still adsorbed irreversibly onto cellulose. Carboxymethyl cellulose (CMC) adsorption onto cellulose and viscoelastic properties and water contents of the adsorbed CMC layers were obtained from a combination of QCM-D and SPR data. The CMC samples formed hydrated and viscoelastic layers compared to the relatively rigid xyloglucan layer. Pectin model surfaces were prepared by pectin adsorption from citric phosphate buffer onto gold substrates. These pectin model surfaces were used for subsequent interaction studies with xyloglucan and enzymatic degradation behavior. There is a strong correlation between the degree of esterification (DE) and film resistance to degradation with the high DE being the most susceptible to degradation. The adsorption of two mixed linkage glucans (MLG), barley and lichen MLG, onto regenerated cellulose (RC) surfaces in the absence and presence of other matrix polysaccharides was studied. Viscoelastic properties of the resulting layer were compared as a function of the proprotion of '-(1''3) linkages with lichen MLG forming softer gel-like layers on RC. The lichen MLG layers were further used for enzymatic degradation studies with respect to enzyme concentration, temperature, pH and ionic strength. These studies show that polymer adsorption is a promising strategy to modify material surfaces and provides fundamental understanding of interactions and biodegradation of cell wall polysaccharides at solid/liquid interfaces.
  • Thumbnail Image
    Adsorption of Blood Proteins onto Polysaccharide Surfaces
    Tan, Xinyi (Virginia Tech, 2016-01-10)
    In this study, surface plasmon resonance (SPR) and quartz crystal microbalance with dissipation monitoring (QCM-D) were combined to investigate the adsorption behavior of two platelet adhesion-related blood proteins, human serum albumin (HSA) and human serum fibrinogen (HSF), on two polysaccharide materials used for hemodialysis membrane applications: regenerated cellulose and cellulose acetate. The study aims to provide insight into the design of novel hemocompatible polysaccharide materials. Information such as real-time adsorption curves, adsorbed amounts, and water contents of the protein layers were obtained and analyzed. The results suggested 1) monolayer adsorption of HSA on both cellulose and cellulose acetate, possibly with different HSA conformations; 2) a multilayer of HSF or some degree of end-on adsorption on both surfaces. The study of HSA adsorption onto cellulose acetate surfaces with different degrees of substitution indicated that the change in content of acetyl groups may not be the main factor governing the adsorbed HSA amount but may affect the conformation of adsorbed HSA molecules.
  • Thumbnail Image
    Adsorption of Xyloglucan onto Cellulose and Cellulase onto Self-assembled Monolayers
    Qian, Chen (Virginia Tech, 2012-04-19)
    Adsorption of xyloglucan (XG) onto thin desulfated nanocrystalline cellulose (DNC) films was studied by surface plasmon resonance spectroscopy (SPR), quartz crystal microbalance with dissipation monitoring (QCM-D), and atomic force microscopy (AFM) measurements. These studies were compared to adsorption studies of XG onto thin sulfated nanocrystalline cellulose (SNC) films and regenerated cellulose (RC) films performed by others. Collectively, these studies show the accessible surface area is the key factor for the differences in surface concentrations observed for XG adsorbed onto the three cellulose surfaces. XG penetrated into the porous nanocrystalline cellulose films. In contrast, XG was confined to the surfaces of the smooth, non-porous RC films. Surprisingly surface charge and cellulose morphology played a limited role on XG adsorption. The effect of the non-ionic surfactant Tween 80 on the adsorption of cellulase onto alkane thiol self-assembled monolayers (SAMs) on gold was also studied. Methyl (-CH3), hydroxyl (-OH) and carboxyl (-COOH) terminated SAMs were prepared. Adsorption of cellulase onto untreated and Tween 80-treated SAMs were monitored by SPR, QCM-D and AFM. The results indicated cellulase adsorption onto SAM-CH3 and SAM-COOH were driven by strong hydrophobic and electrostatic interactions, however, hydrogen bonding between cellulase and SAM-OH was weak. Tween 80 effectively hindered the adsorption of cellulase onto hydrophobic SAM-CH3 substrates. In contrast, it had almost no effect on the adsorption of cellulase onto SAM-OH and SAM-COOH substrates because of its reversible adsorption on these substrates.
  • Thumbnail Image
    Adsorption of Xyloglucan onto Thin Films of Cellulose Nanocrystals and Amorphous Cellulose: Film Thickness Effects
    Kittle, Joshua D.; Qian, Chen; Edgar, Emma; Roman, Maren; Esker, Alan R. (American Chemical Society, 2018-10-01)
  • Thumbnail Image
    Advanced Applications of Raman Spectroscopy for Environmental Analyses
    Lahr, Rebecca Halvorson (Virginia Tech, 2014-01-09)
    Due to an ever-increasing global population and limited resource availability, there is a constant need for detection of both natural and anthropogenic hazards in water, air, food, and material goods. Traditionally a different instrument would be used to detect each class of contaminant, often after a concentration or separation protocol to extract the analyte from its matrix. Raman spectroscopy is unique in its ability to detect organic or inorganic, airborne or waterborne, and embedded or adsorbed analytes within environmental systems. This ability comes from the inherent abilities of the Raman spectrometer combined with concentration, separation, and signal enhancement provided by drop coating deposition Raman (DCDR) and surface-enhanced Raman spectroscopy (SERS). Herein the capacity of DCDR to differentiate between cyanotoxin variants in aqueous solutions was demonstrated using principal component analysis (PCA) to statistically demonstrate spectral differentiation. A set of rules was outlined based on Raman peak ratios to allow an inexperienced user to determine the toxin variant identity from its Raman spectrum. DCDR was also employed for microcystin-LR (MC-LR) detection in environmental waters at environmentally relevant concentrations, after pre-concentration with solid-phase extraction (SPE). In a cellulose matrix, SERS and normal Raman spectral imaging revealed nanoparticle transport and deposition patterns, illustrating that nanoparticle surface coating dictated the observed transport properties. Both SERS spectral imaging and insight into analyte transport in wax-printed paper microfluidic channels will ultimately be useful for microfluidic paper-based analytical device (𝜇PAD) development. Within algal cells, SERS produced 3D cellular images in the presence of intracellularly biosynthesized gold nanoparticles (AuNP), documenting in detail the molecular vibrations of biomolecules at the AuNP surfaces. Molecules involved in nanoparticle biosynthesis were identified at AuNP surfaces within algal cells, thus aiding in mechanism elucidation. The capabilities of Raman spectroscopy are endless, especially in light of SERS tag design, coordinating detection of analytes that do not inherently produce strong Raman vibrations. The increase in portable Raman spectrometer availability will only facilitate cheaper, more frequent application of Raman spectrometry both in the field and the lab. The tremendous detection power of the Raman spectrometer cannot be ignored.
  • Thumbnail Image
    Arabinoglucuronoxylan and Arabinoxylan Adsorption onto Regenerated Cellulose Films
    Ni, Ying (Virginia Tech, 2013-09-03)
    Cellulose and hemicelluloses have attracted increasing interest as renewable biopolymers because of their abundance. Furthermore, the recognition of biomass as a sustainable and renewable source of biofuels has driven research into the assembly and disassembly of polymers within plant cell walls. Cellulose thin films are useful in the study of interactions between cellulose and hemicelluloses, and quartz crystal microbalances with dissipation monitoring (QCM-D), surface plasmon resonance (SPR) and atomic force microscopy (AFM) are widely used to investigate polymer adsorption/desorption at liquid/solid interfaces. In this study, smooth trimethylsilyl cellulose (TMSC) films were spincoated onto gold QCM-D sensors and hydrolyzed into ultrathin cellulose films upon exposure to aqueous HCl vapor. The adsorption of arabinoglucuronoxylan (AGX) and arabinoxylan (AX) onto these cellulose surfaces was studied. The effects of structure, molar mass and ionic strength of the solution were considered. Increasing ionic strength increased AGX and AX adsorption onto cellulose. While AGX showed greater adsorption onto cellulose than AX by QCM-D, the trend was reversed in SPR experiments. The combination of QCM-D and SPR data showed a greater amount of water was trapped within the AX films. Both adsorbed AGX and AX films were subsequently visualized by AFM. Images from AFM showed AGX and AX adsorbed as aggregates from water, while AGX and AX adsorbed from CaCl2 yielded smaller xylan particles with more numerous globular structures on the cellulose surfaces. Images from AFM of xylan films on bare gold surfaces also showed layers of uniform aggregates that were consistent with AX and AGX aggregation in solution.
  • Thumbnail Image
    Bio-inspired Cellulose Nanocomposites
    Pillai, Karthik (Virginia Tech, 2011-04-26)
    Natural composites like wood are scale-integrated structures that range from molecular to the macroscopic scale. Inspired by this design, layer-by-layer (LbL) deposition technique was used to create lignocellulosic composites from isolated wood polymers namely cellulose and lignin, with a lamellar architecture. In the first phase of the study, adsorption of alkali lignin onto cationic surfaces was investigated using a quartz crystal microbalance with dissipation monitoring (QCM-D). Complete coverage of the cationic surface with alkali lignin occured at low solution concentration; large affinity coefficients were calculated for this system at differing pH levels. Adsorption studies with organosolv lignin in an organic solvent, and spectroscopic analysis of mixtures of cationic polymer with alkali lignin revealed a non-covalent interaction. The work demonstrated how noncovalent interactions could be exploited to molecular organize thin polyphenolic biopolymers on cationic surfaces. The second phase of the study examined the adsorption steps during the LbL assembly process to create novel lignocellulosic composites. LbL assembly was carried out using oxidized nanocellulose (NC) and lignin, along with a cationic polymer poly(diallyldimethylammonium chloride) (PDDA). QCM-D was used to follow the sequential adsorption process of the three different polymers. Two viscoelastic models, namely Johannsmann and Voigt, were respectively used to calculate the areal mass and thickness of the adsorbed layers. Atomic force microscopy studies showed a complete coverage of the surface with lignin in all the disposition cycles, however, surface coverage with NC was seen to increase with the number of layers. Free-standing composite films were obtained when the LbL process was carried out for 250 deposition cycles (500 bilayers) on a cellulose acetate substrate, following the dissolution of the substrate in acetone. Scanning electron microscopy of the cryo-fractured cross-sections showed a lamellar structure, and the thickness per adsorption cycle was estimated to be 17 nm. The third phase of the study investigated the effect of LbL ordering of the polymers versus a cast film composed of a blended mixture of the polymers, using dynamic mechanical analysis. A tan ï ¤ peak was observed in the 30 – 40 ºC region for both films, which was observed in the neat NC film. Heating of the samples under a compressive force produced opposite effects in the films, as the LbL films exhibited swelling, whereas the cast films showed densification. The apparent activation energy of this transition (65 – 80 kJ mol-1) in cast films, calculated based on the Arrhenius equation was found to be coincident to those reported for the ï ¢ transition of amorphous cellulose. The peak was seen to disappear in case of LbL films in the second heat, whereas it was recurring in case of cast films of the blended mixture, and neat NC films. Altogether, the together the work details a novel path to integrate an organized lignin and cellulose molecular structure, albeit modified from their native form, into a three-dimensional composite material.
  • Thumbnail Image
    Bioactive Cellulose Nanocrystal Reinforced 3D Printable Poly(epsilon-caprolactone) Nanocomposite for Bone Tissue Engineering
    Hong, Jung Ki (Virginia Tech, 2015-05-07)
    Polymeric bone scaffolds are a promising tissue engineering approach for the repair of critical-size bone defects. Porous three-dimensional (3D) scaffolds play an essential role as templates to guide new tissue formation. However, there are critical challenges arising from the poor mechanical properties and low bioactivity of bioresorbable polymers, such as poly(epsilon-caprolactone) (PCL) in bone tissue engineering applications. This research investigates the potential use of cellulose nanocrystals (CNCs) as multi-functional additives that enhance the mechanical properties and increase the biomineralization rate of PCL. To this end, an in vitro biomineralization study of both sulfuric acid hydrolyzed-CNCs (SH-CNCs) and surface oxidized-CNCs (SO-CNCs) has been performed in simulated body fluid in order to evaluate the bioactivity of the surface functional groups, sulfate and carboxyl groups, respectively. PCL nanocomposites were prepared with different SO-CNC contents and the chemical/physical properties of the nanocomposites were analyzed. 3D porous scaffolds with fully interconnected pores and well-controlled pore sizes were fabricated from the PCL nanocomposites with a 3D printer. The mechanical stability of the scaffolds were studied using creep test under dry and submersion conditions. Lastly, the biocompatibility of CNCs and 3D printed porous scaffolds were assessed in vitro. The carboxyl groups on the surface of SO-CNCs provided a significantly improved calcium ion binding ability which could play an important role in the biomineralization (bioactivity) by induction of mineral formation for bone tissue engineering applications. In addition, the mechanical properties of porous PCL nanocomposite scaffolds were pronouncedly reinforced by incorporation of SO-CNCs. Both the compressive modulus and creep resistance of the PCL scaffolds were enhanced either in dry or in submersion conditions at 37 degrees Celsius. Lastly, the biocompatibility study demonstrated that both the CNCs and material fabrication processes (e.g., PCL nanocomposites and 3D printing) were not toxic to the preosteoblasts (MC3T3 cells). Also, the SO-CNCs showed a positive effect on biomineralization of PCL scaffolds (i.e., accelerated calcium or mineral deposits on the surface of the scaffolds) during in vitro study. Overall, the SO-CNCs could play a critical role in the development of scaffold materials as a potential candidate for reinforcing nanofillers in bone tissue engineering applications.
  • Thumbnail Image
    Bioactive Cellulose Nanocrystal-Poly(epsilon-Caprolactone) Nanocomposites for Bone Tissue Engineering Applications
    Hong, Jung Ki; Cooke, Shelley L.; Whittington, Abby R.; Roman, Maren (2021-02-25)
    3D-printed bone scaffolds hold great promise for the individualized treatment of critical-size bone defects. Among the resorbable polymers available for use as 3D-printable scaffold materials, poly(epsilon-caprolactone) (PCL) has many benefits. However, its relatively low stiffness and lack of bioactivity limit its use in load-bearing bone scaffolds. This study tests the hypothesis that surface-oxidized cellulose nanocrystals (SO-CNCs), decorated with carboxyl groups, can act as multi-functional scaffold additives that (1) improve the mechanical properties of PCL and (2) induce biomineral formation upon PCL resorption. To this end, an in vitro biomineralization study was performed to assess the ability of SO-CNCs to induce the formation of calcium phosphate minerals. In addition, PCL nanocomposites containing different amounts of SO-CNCs (1, 2, 3, 5, and 10 wt%) were prepared using melt compounding extrusion and characterized in terms of Young's modulus, ultimate tensile strength, crystallinity, thermal transitions, and water contact angle. Neither sulfuric acid-hydrolyzed CNCs (SH-CNCs) nor SO-CNCs were toxic to MC3T3 preosteoblasts during a 24 h exposure at concentrations ranging from 0.25 to 3.0 mg/mL. SO-CNCs were more effective at inducing mineral formation than SH-CNCs in simulated body fluid (1x). An SO-CNC content of 10 wt% in the PCL matrix caused a more than 2-fold increase in Young's modulus (stiffness) and a more than 60% increase in ultimate tensile strength. The matrix glass transition and melting temperatures were not affected by the SO-CNCs but the crystallization temperature increased by about 5.5 degrees C upon addition of 10 wt% SO-CNCs, the matrix crystallinity decreased from about 43 to about 40%, and the water contact angle decreased from 87 to 82.6 degrees. The abilities of SO-CNCs to induce calcium phosphate mineral formation and increase the Young's modulus of PCL render them attractive for applications as multi-functional nanoscale additives in PCL-based bone scaffolds.
  • Thumbnail Image
    Biomolecular Controls on Calcium Carbonate Formation by Amorphous and Classical Pathways: Insights from Measurements of Nucleation Rates and Isotope Tracers
    Giuffre, Anthony J. (Virginia Tech, 2015-04-26)
    Calcified skeletons are produced within complex assemblages of proteins and polysaccharides whose roles in mineralization are not well understood. Researchers have long postulated that living organisms utilize the macromolecules of organic matrices to actively guide the formation of crystal structures. The timing and placement of the subsequent minerals that form are most easily controlled during nucleation; however, a physical and chemical picture of how organic functional group chemistry influences the initial stages of nucleation is not yet established. These processes are further complicated by the realization that carbonate biominerals can form by an amorphous to crystalline transformation process, which has prompted the question of how chemical signatures are recorded during mineralization. Investigations of mineralization processes such as the kinetics of nucleation and the transformation of amorphous calcium carbonate (ACC) to crystalline products are critical to building a better understanding of biomineral formation. Only from that fundamental basis can one begin to decipher changes in climate and seawater chemistry over geologic time and by recent anthropogenic effects. This dissertation presents the findings from experimental studies of the thermodynamics and kinetics of multiple mineral formation processes, including nucleation and transformation from an amorphous phase. The kinetics of calcite nucleation onto a suite of high-purity polysaccharide (PS) substrates were quantified under controlled conditions. Nucleation rates were measured as a function of 1) supersaturation extending above and below ACC solubility and 2) ionic strength extending to seawater salinity. These conditions decipher the chemical interactions between the PS substrate, calcite crystal, and solution. These investigations show the energy barrier to calcite formation is regulated by competing interfacial energies between the substrate, crystal, and liquid. The energy barriers to nucleation are PS-specific by a systematic relationship to PS charge density and substrate structure that is rooted in minimization of the competing substrate-crystal and substrate-liquid interfacial energies. The data also suggest ionic strength regulates nucleation barriers through substrate-liquid and crystal-liquid interfacial energetics. In a second experimental study, stable isotope labeling was used to directly probe the transformation pathway. Four processes were considered: dissolution-reprecipitation, solid-state, or combinations of these end member processes. Isotope measurements of calcite crystals that transform from ACC have signatures that are best explained by dissolution-reprecipitation. The extent of isotopic mixing correlates with the amount of ACC transferred and the time to transformation, suggesting the calcite crystals are recording the changing local solution environment during the transformation. These investigations into different mineralization mechanisms build a framework for how functional group chemistries of organic molecules regulate mineralization and the resulting isotopic and elemental signatures in the calcite. This may provide useful insights to interpreting chemical signatures of carbonate biominerals in fossil record and understanding ocean chemistry changes throughout geologic time.
  • Thumbnail Image
    Carboxymethylcellulose Acetate Butyrate Water-Dispersions as Renewable Wood Adhesives
    Paris, Jesse Loren (Virginia Tech, 2010-08-05)
    Two commercial carboxymethylcellulose acetate butyrate (CMCAB) polymers, high and low molecular weight (MW) forms, were analyzed in this study. High-solids water-borne dispersions of these polymers were studied as renewable wood adhesives. Neat polymer analyses revealed that the apart from MW, the CMCAB systems had different acid values, and that the high MW system was compromised with gel particle contaminants. Formulation of the polymer into water-dispersions was optimized for this study, and proved the "direct method", in which all formulation components were mixed at once in a sealed vessel, was the most efficient preparation technique. Applying this method, 4 high-solids water dispersions were prepared and evaluated with viscometry, differential scanning calorimetry, dynamic mechanical analysis, light and fluorescence microscopy, and mode I fracture testing. Thermal analyses showed that the polymer glass transition temperature significantly increased when bonded to wood. CMCAB dispersions produced fairly brittle adhesive-joints; however, it is believed toughness can likely be improved with further formulation optimization. Lastly, dispersion viscosity, film formation, adhesive penetration and joint-performance were all dependent on the formulation solvents, and moreover, these properties appeared to correlate with each other.
  • Thumbnail Image
    Catechyl-lignin tissues in Vanilla orchid and Candlenut: structure/property studies
    Ristanti, Eky Yenita (Virginia Tech, 2023-05-24)
    In 2012, a new type of lignin, catechyl (C)-lignin was found in the seed coat of vanilla orchid (Vanilla planifolia) and Melocactus cacti, and later in the nutshell of Aleurites moluccana (candlenut). This caffeyl alcohol homopolymer is the exclusive lignin in vanilla seed coat but separated in time and/or location with guaiacyl (G)-lignin in candlenut. Unlike conventional guaiacyl/syringyl (G/S-lignins) with alkyl-aryl ether linkages, intermonomer linkages in C-lignin are connected by benzodioxane linkages which are stiffer than alkyl-aryl ether linkages. C-lignin is unusually stable against acid-catalyzed cleavage. Tissues with C-lignin are expected to exhibit high glass transition temperature (Tg) compared to tissues with G/S/H-lignin. C-lignin also probably shows high crystallinity due to its highly linear-homopolymer structure. The ability of some seed coats/nutshells in angiosperms to synthesize a new type of lignin is another level of lignin evolution. However, the role of C-lignin related to the function of the seed coat is unclear while it exhibits different behaviors to the regular G/S/H-lignin. These points motivated us to conduct cell-wall structure/property studies in the context of plant evolution, using microscopy, X-ray diffraction (XRD) and dynamic mechanical analysis (DMA). Light and electron microscopes were used to identify cell's size and type of intact and macerated vanilla seed coat and candlenut shell. Vanilla seeds are tiny, sized approximately 300μm and the surface is covered with dark-colored seed coat. Candlenut is slightly smaller than walnut, with uneven, hard, dark brown shell covering the nut. Microscopy observations indicated that both seed coat and nutshell are dominated by highly lignified cells, known as sclereids. The types of sclereids in vanilla seed coat and candlenut shell are different; vanilla seed coat has ostoesclereid-type cells, while candlenut shell has macrosclereid-type cells. XRD was used to study tissue with C-lignin crystallinity by comparing diffractograms of vanilla seed coat and candlenut shell to Southern Yellow Pine wood diffractograms. The Southern Yellow Pine wood diffractogram corresponds to a typical native cellulose in higher plants, that is cellulose I allomorph. Diffractogram XRD analysis on vanilla seed coat and candlenut shell shows similarities to Southern Yellow Pine native cellulose, suggesting that cellulose is the contributor for crystallinity in seed coat and nutshell, and this also indicated that tissues with C-lignin is not crystalline. Crystallinities of vanilla seed coat and candlenut shell determined using peak deconvolution methods were about half of Southern Yellow Pine crystallinity. DMA was used to measure Tg in vanilla seed coat and candlenut shell. Measurements were conducted in solvent-submersion mode using organic plasticizers to reduce the Tg to non-damaging temperatures. DMA measurement of vanilla seed coat and candlenut shell is challenging due to specimen size and shape. Specimen preparation for DMA measurement included seed coat purification for vanilla and cutting/milling for candlenut shell followed by specimen saturation in plasticizers. Compressive-torsion DMA was used to allow tiny specimens gripping. Vanilla seed coats exhibited higher glass transition temperature compared to wood, while candlenut shells exhibited various Tgs depending on specimen type/size.
  • Thumbnail Image
    CELL 256: Role of dispersion and polar interactions in the adsorption of cellulases onto lignin
    Roman, Maren; Jiang, Feng; Chen, Qian; Esker, Alan R. (2018-03)
    Residual lignin in pretreated biomass hinders its enzymatic hydrolysis. Nonionic surfactants are known to have beneficial effects on the enzymatic hydrolysis of lignocellulosic biomass but their mechanisms of action at the molecular level are incompletely understood. This study investigates the effect of a nonionic surfactant, Tween 80, on the adsorption of cellulases onto model lignin substrates. Lignin substrates were prepared by spin coating of flat substrates with three different types of lignin: organosolv lignin, kraft lignin, and milled wood lignin. Tween 80 and cellulase adsorption onto the lignin substrates was analyzed with a quartz crystal microbalance with dissipation monitoring. Supporting experiments of Tween 80 and cellulase adsorption onto self-assembled monolayers with lignin-related functional groups provided critical insights into the role of polar and dispersive functional groups in lignin on cellulase adsorption and the effect of Tween 80 on the process.
  • Thumbnail Image
    Cellulose Nanocrystals: Size Characterization and Controlled Deposition by Inkjet Printing
    Navarro, Fernando (Virginia Tech, 2010-06-29)
    Inkjet printing has generated considerable interest as a technique for the patterning of functional materials in the liquid phase onto a substrate. Despite its high promise, the phenomena associated with inkjet printing remain incompletely understood. This research project investigates inkjet printing of cellulose nanocrystals (CNCs) as a possible method for the fabrication of cellulose micropatterns. CNCs were prepared from wood pulp by H₂SO₄ hydrolysis and characterized in terms of length, width, and thickness distributions by atomic force microscopy (AFM) and dynamic light scattering. Aqueous CNC suspensions were characterized in terms of shear viscosity with a rheometer. Glass substrates were cleaned with a detergent solution, aqua regia, or a solvent mixture, and characterized in terms of surface chemical composition, surface free energy, polarity, roughness, ζ-potential, and surface charge distribution in air by X-ray photoelectron spectroscopy, contact angle measurements, AFM, streaming potential, and scanning Kelvin probe microscopy (SKPM). Additionally, poly(ethylene glycol)-grafted glass substrates were prepared and characterized in terms of surface free energy, polarity, and roughness. Aqueous CNC suspensions were printed in different patterns onto the different glass substrates with a commercial, piezoelectric drop-on-demand inkjet printer. Inkjet deposited droplet residues and micropatterns were analyzed by AFM, scanning electron microscopy, and polarized-light microscopy. At low CNC concentrations (0.05 wt %), inkjet-deposited droplets formed ring-like residues due to the "coffee drop effect". The "coffee drop effect" could be suppressed by the use of higher CNC concentrations. The resulting dot-like droplet residues exhibited Maltese cross interference patterns between crossed polarizers, indicating a radial orientation of the birefringent, elongated CNCs in these residues. The observed Maltese cross interference patterns represent unprecedented indirect evidence for a center-to-edge radial flow in drying droplets. The degree of definition of the micropatterns depended strongly on the surface properties of the glass substrates. Well-defined micropatterns were obtained on aqua regia-cleaned substrates. In addition to the surface free energy and polarity, other factors seemed to play a role in the formation of the inkjet-printed micropatterns. If these factors can be identified and controlled, inkjet deposition of CNCs could become an attractive method for the fabrication of cellulose micropatterns.
  • Thumbnail Image
    Characterization of PF Resol/Isocyanate Hybrid Adhesives
    Riedlinger, Darren Andrew (Virginia Tech, 2008-02-01)
    Water-based resol phenol formaldehyde, PF, and organic polymeric methylenebis(phenylisocyanate), pMDI, are the two primary choices for the manufacture of exterior grade wood-based composites. This work addresses simple physical blends of pMDI dispersed in PF as a possible hybrid wood adhesive. Part one of this study examined the morphology of hybrid blends prepared using commercially available PF and pMDI. It was found that the blend components rapidly reacted such that the dispersed pMDI droplets became encased in a polymeric membrane. The phase separation created during liquid/liquid blending appeared to have been preserved in the cured, solid-state. However, substantial interdiffusion and copolymerization between blend components also appeared to have occurred according to measured cure rates, dynamic mechanical analysis, and atomic force microscopy. In the second part of this study a series of PF resins was synthesized employing the so-called "split-cook" method, and by using a range of formaldehyde/phenol and NaOH/phenol mole ratios. These neat PF resins were subjected to the following analyses: 1) steady-state flow viscometry, 2) free formaldehyde titration, 3) non-volatile solids determination, 4) size exclusion chromatography, 5) quantitative solution-state ¹³C nuclear magnetic resonance, NMR, 6) differential scanning calorimetry, 7) parallel-plate oscillatory cure rheology, and 8) dielectric spectroscopy. The neat PF analytical results were unremarkable with one exception; NMR revealed that the formaldehyde/phenol mole ratio in one resin substantially differed from the target mole ratio. The neat PF resins were subsequently used to prepare of series of PF/pMDI blends in a ratio of 75 parts PF solids to 25 parts pMDI solids. The resulting PF/pMDI blends were subjected to the following analyses: 1) differential scanning calorimetry, 2) parallel-plate oscillatory cure rheology, and 3) dielectric spectroscopy. Similar to what was inferred in part one of this study, both differential scanning calorimetry (DSC) and oscillation cure rheology demonstrated that cure of the PF continuous phase was substantially altered and accelerated by pMDI. However within actual wood bondlines, dielectric analysis detected little variation in cure speed between any of the formulations, both hybrid and neat PF. Furthermore, the modulated DSC curing experiments detected some latent reactivity in the hybrid system, both during initial isothermal curing and subsequent thermal scanning. The latent reactivity may suggest that a significant diffusion barrier existed between blend components, preventing complete reaction of hybrid blends even after thermal scanning up to 200 °C. Part three of this work examined the bonded wood mode-I fracture performance of hybrid resins as a function of the resol formaldehyde/phenol ratio and also the alkali content. A moderate increase in unweathered fracture toughness was observed for hybrid formulations relative to neat PF. Following accelerated weathering, the durability of the hybrid blends was promising: weathered hybrid toughness was equivalent to that of weathered neat PF. While the resol F/P ratio and alkali content both influenced hybrid fracture toughness, statistical modeling revealed interaction between these variables that complicated result interpretation: the influence of hybrid alkali content depended heavily on each formulation's specific F/P ratio, and vice versa.
  • Thumbnail Image
    Chemical Modification of Alginates in Organic Media
    Pawar, Siddhesh Nitin (Virginia Tech, 2013-07-25)
    Alginates are (1and4) linked linear copolysaccharides composed of B-D-mannuronic acid (M) and its C-5 epimer, a-L-guluronic acid (G). Several strategies to synthesize organically modified alginate derivatives have been reported, but almost all chemistries are performed in either aqueous or aqueous-organic media. The ability to react alginates homogeneously in organic solvents would open up access to a wide range of new chemistries and derivatives. However, past attempts have been restricted by the absence of methods for alginate dissolution in organic media. We therefore report a strategy to solubilize tetrabutylammonium (TBA) salts of alginic acid in polar aprotic solvents containing tetrabutylammonium fluoride (TBAF). Acylation of TBA-alginate was performed in DMSO/TBAF to get products with DSacetyl up to ~ 1.0. We further report that by using appropriate solvent conditions, placement of acyl groups can be controlled to achieve either random or M-selective substitution. Alginate acetates synthesized in an M-selective fashion were used to study the ability of these derivatives to form Ca-crosslinked hydrogels. Detailed structure-property analyses were performed to identify acetylation reaction conditions and product properties that may be ideal for hydrogel formation. Furthermore, alginate esters were synthesized via modification of carboxylate groups on the backbone. These derivatives dissolved in polar aprotic solvents without the need to add TBAF. A proof of concept study showed their utility in the solubility enhancement of the poorly water soluble flavonoid naringenin.
  • Thumbnail Image
    Chitosan-Cellulose Nanocrystal Polyelectrolyte Complex Particles: Preparation, Characterization, and In Vitro Drug Release Properties
    Wang, Hezhong (Virginia Tech, 2009-10-22)
    Polyelectrolyte complexes (PECs) between chitosan, a mucoadhesive, intestinal mucosal permeability-enhancing polysaccharide, and cellulose nanocrystals, rod-like cellulose nanoparticles with sulfate groups on their surface, have potential applications in oral drug delivery. The purpose of this research was to develop an understanding of the formation and properties of chitosan–cellulose nanocrystal PECs and determine their in vitro drug release properties, using caffeine and ibuprofen as model drugs. Cellulose nanocrystals were prepared by sulfuric acid hydrolysis of bleached wood pulp. Chitosans with three different molecular weights (81, 3·103, 6·103 kDa) and four different degrees of deacetylation (77, 80, 85, 89%) were used. PEC formation was studied by turbidimetric titration. PEC particles were characterized by FT-IR spectroscopy, scanning electron microscopy, dynamic light scattering, and laser Doppler electrophoresis. The formation and properties of chitosan–cellulose nanocrystal PEC particles were governed by the strong mismatch in the densities of the ionizable groups. The particles were composed primarily of cellulose nanocrystals. Particle shape and size strongly depended on the mixing ratio and pH of the surrounding medium. The ionic strength of the surrounding medium, and the molecular weight and degree of deacetylation of chitosan had a minor effect. Release of caffeine from the chitosan–cellulose nanocrystal PEC particles was rapid and uncontrolled. Ibuprofen-loaded PEC particles showed no release in simulated gastric fluid and rapid release in simulated intestinal fluid. Further evaluation studies should focus on the expected mucoadhesive and permeability-enhancing properties of chitosan–cellulose nanocrystal PEC particles.
  • Thumbnail Image
    Cytotoxicity and Cellular Uptake of Cellulose Nanocrystals
    Dong, Shuping; Hirani, Anjali A.; Colacino, Katelyn R.; Lee, Yong Woo; Roman, Maren (2012-09-21)
    There is growing evidence that filamentous nanoparticles offer advantages over spherical ones in drug delivery applications. The purpose of this study was to assess the potential of rod-like, plant-derived cellulose nanocrystals (CNCs) for nanomedical uses. Besides a nonspherical morphology, their facile bioconjugation, surface hydrophilicity and small size render CNCs promising drug carriers. The cytotoxicity of CNCs against nine different cell lines (HBMEC, bEnd.3, RAW 264.7, MCF-10A, MDA-MB-231, MDA-MB-468, KB, PC-3 and C6) was determined by MTT and LDH assay. CNCs showed no cytotoxic effects against any of these cell lines in the concentration range and exposure time studied (0–50 µg/mL and 48 h, respectively). Cellular uptake of fluorescein-50 - isothiocyanate-labeled CNCs by these cell lines, quantified with a fluorescence microplate reader, was minimal. The lack of cytotoxicity and the low nonspecific cellular uptake support our hypothesis that CNCs are good candidates for nanomedical applications.
  • Thumbnail Image
    Design of Functional Polyesters for Electronic and Biological Applications
    Nelson, Ashley M. (Virginia Tech, 2015-08-12)
    Melt polymerization and novel monomers enabled the synthesis of polyesters for electronic and biological applications. Inspiration from nature and a passion for environmental preservation instigated an emphasis on the incorporation of renewable resources into polymeric materials. Critical analysis of current research surrounding bisphenol-A replacements and ioncontaining segmented polyurethanes aided in identifying benchmark polymers, including limitations, challenges, and future needs. Structure-property-morphology relationships were investigated to evaluate the polymers for success in the proposed applications as well as to improve understanding of polyester compositions to further design and develop sophisticated polymers for emerging applications. Aiming to utilize the reported [2 + 2] cycloaddition of the known mesogen 4,4’-dimethyltrans-stilbene dicarboxylate (SDE) to overcome ultraviolet (UV) induced degradation issues in electronic encasings, the synthesis of copolyesters containing SDE ensued. 1,6-Hexanediol (HD) and 1,4-butanediol comonomers in varying weight ratios readily copolymerized with SDE under melt transesterification conditions to afford a systematic series of copolyesters. Differential scanning calorimetry revealed all copolyesters exhibited liquid crystalline transitions and melting temperatures ranged from 196 °C – 317 °C. Additionally, melt rheology displayed shear thinning to facilitate melt processing. Compression molded films exhibited high storage moduli, a glassy plateau until the onset of flow, and tensile testing revealed a Young’s iii modulus of ~900 MPa for poly(SDE-HD). These properties enable a wide range of working temperatures and environments for electronic applications. Adding complexity to linear liquid crystalline copolyesters, copolymerization with oligomeric hydroxyl-functionalized polyethers afforded segmented liquid crystalline copolyesters. 4,4’-Biphenyl dicarboxylate (BDE), commercially available diols containing 4, 5, 6, 8, or 10 methylene units, and introducing poly(tetramethylene oxide) or a Pluronic® triblock oligoethers in varying weight % were used to synthesize multiple series of segmented copolyesters. Comparing melting transitions as a function of methylene spacer length elucidated the expected even-odd effect and melting temperatures ranged from 150 °C to 300 °C. Furthermore, incorporating the flexible soft segment did not prevent formation of a liquid crystalline morphology. Complementary findings between differential scanning calorimetry and small-angle X-ray scattering confirmed a microphase-separated morphology. Thermomechanical analysis revealed tunable plateau moduli and temperature windows based on both soft segment content and methylene spacer length, and tensile testing showed the strain at break doubled from 75 weight % to 50 weight % hard segment content. The same compositions Young’s moduli decreased from 107 ± 12 MPa at 75 weight % hard segment to 19 ± 1 MPa with 50 weight % hard segment, demonstrating the mechanical trade-off and range of properties possible with small compositional changes. These segmented copolyesters could find use in high-performance applications including electronic and aerospace industries. A two-step synthesis transformed caffeine into a novel caffeine-containing methacrylate (CMA). Conventional free radical copolymerization with a comonomer known to provide a low glass transition temperature (Tg), 2-ethylhexyl methacrylate (EHMA), allowed the investigation of the effect of small amounts of pendant caffeine on polymer properties. Thermal and iv thermomechanical testing indicated CMA incorporation dramatically increased the storage modulus, however, a microphase-separated morphology was not attained. Association of the pendant caffeine groups through non-covalent π-π stacking could present opportunities for novel thermoplastics and it is proposed that placing the pendant group further from the backbone, and potentially increasing the concentration, could aid in promoting microphase-separation. Alkenes are reactive sites for placing functional groups, particularly those required for polyester synthesis. Methyl 9-decenoate (9-DAME), a plant-based fatty acid, provided a platform for novel biodegradable, renewable, polyesters. A formic acid hydration reaction generated an isomeric mixture of AB hydroxyester or AB hydroxyacid monomers for melt polymerization. Thermal analysis elucidated the plant-based polyesters exhibited a single transition, a Tg of about -60 °C. Aliphatic polyesters commonly crystallize, thus the isomeric mixture of secondary alcohols seemed to introduce enough irregularity to prevent crystallization. These polyesters offer an amorphous, biodegradable, sustainable replacement for applications currently using semi-crystalline poly(ε-caprolactone), which is not obtained from renewable monomers and also exhibits a -60 °C Tg. Additional applications requiring low-Tg polymers such as pressure sensitive adhesives or thermoplastic elastomers could also benefit from these novel polyesters. 9-DAME also was transformed into an ABB’ monomer after an epoxidation and subsequent hydrolysis. Successful gelation under melt transesterification conditions provided evidence that the multifunctional monomer could perform as a renewable, biodegradable, branching and/or crosslinking agent. Novel copolyesters comprised of a bromomethyl imidazolium diol and adipic acid demonstrated potential as non-viral gene delivery vectors. Melt polycondensation produced water dispersible polyesters which bound deoxyribonucleic acid at low N/P ratios. The v polyplexes showed stability in water over 24 h and no cytotoxic effect on human cervical cancer cells (HeLa). A luciferase transfection assay revealed the copolyesters successfully underwent endocytosis and released the nucleic acid better than controls. The copolyesters with pendant imidazolium functionality also provided tunable Tgs, -41 °C to 40 °C, and the ability to electrospin into fibers upon blending with poly(ethylene oxide). These additional properties furthered potential applications to include pressure sensitive adhesives and biocompatible antibacterial bandages.