VTechWorks staff will be away for the Thanksgiving holiday beginning at noon on Wednesday, November 27, through Friday, November 29. We will resume normal operations on Monday, December 2. Thank you for your patience.

Browsing by Author "Yang, Hee Doo"

Now showing 1 - 2 of 2
  • Thumbnail Image
    Design, Manufacturing, and Control of Soft and Soft/Rigid Hybrid Pneumatic Robotic Systems
    Yang, Hee Doo (Virginia Tech, 2019-04-29)
    Soft robotic systems have recently been considered as a new approach that is in principle better suited for tasks where safety and adaptability are important. That is because soft materials are inherently compliant and resilient in the event of collisions. They are also lightweight and can be low-cost; in general, soft robots have the potential to achieve many tasks that were not previously possible with traditional robotic systems. In this paper, we propose a new manufacturing process for creating multi-chambered pneumatic actuators and robots. We focus on using fabric as the primary structural material, but plastic films can be used instead of textiles as well. We introduce two different methods to create layered bellows actuators, which can be made with a heat press machine or in an oven. We also describe origami-like actuators with possible corner structures. Moreover, the fabrication process permits the creation of soft and soft/rigid hybrid robotic systems, and enables the easy integration of sensors into these robots. We analyze various textiles that are possibly used with this method, and model bellows actuators including operating force, restoring force, and estimated geometry with multiple bellows. We then demonstrate the process by showing a bellows actuator with an embedded sensor and other fabricated structures and robots. We next present a new design of a multi-DOF soft/rigid hybrid robotic manipulator. It contains a revolute actuator and several roll-pitch actuators which are arranged in series. To control the manipulator, we use a new variant of the piece-wise constant curvature (PCC) model. The robot can be controlled using forward and inverse kinematics with embedded inertial measurement units (IMUs). A bellows actuator, which is a subcomponent of the manipulator, is modeled with a variable-stiffness spring, and we use the model to predict the behavior of the actuator. With the model, the roll-pitch actuator stiffnesses are measured in all directions through applying forces and torques. The stiffness is used to predict the behavior of the end effector. The robotic system introduced achieved errors of less than 5% when compared to the models, and positioning accuracies of better than 1cm.
  • Thumbnail Image
    Modeling and Analysis of a Novel Pneumatic Artificial Muscle and Pneumatic Arm Exoskeleton
    Yang, Hee Doo (Virginia Tech, 2017-06-29)
    The soft robotics field is developing rapidly and is poised to have a wide impact in a variety of applications. Soft robots have intrinsic compliance, offering a number of benefits as compared to traditional rigid robots. Compliance can provide compatibility with biological systems such as the human body and can provide some benefits for human safety and control. Further research into soft robots can be advanced by further development of pneumatic actuators. Pneumatic actuators are a good fit for exoskeleton robots because of their light weight, small size, and flexible materials. This is because a wearable robot should be human friendly, therefore, it should be light weight, slim, powerful, and simple. In this paper, a novel pneumatic artificial muscle using soft materials including integrated electronics for wearable exoskeletons is proposed. We describe the design, fabrication, and evaluation of the actuator, as well as the manufacturing process used to create it. Compared to traditional pneumatic muscle actuators such as the McKibben actuator and new soft actuators that were recently proposed, the novel actuator overcomes shortcomings of prior work. This is due to the actuator's very high contraction ratio that can be controlled by the manufacturing process. In this paper, we describe the design, fabrication, and evaluation of a novel pneumatic actuator that can accommodate integrated electronics for displacement and pressure measurements used for data analysis and control. The desired performance characteristics for the actuator were 100 ~ 400N at between 35kPa and 105kPa, and upon testing we found almost 120 ~ 300N which confirms that these actuators may be suitable in soft exoskeleton applications with power requirements comparable to rigid exoskeletons. Furthermore, a novel soft pneumatic elbow exoskeleton based on the pneumatic actuator concept and manufacturing process is presented. Each structure is designed and manufactured with all fabric. The distally-worn structure is only 300g, which is light weight for an arm exoskeleton, and the design is simple, leading to a low materials cost.