Browsing by Author "Wang, Ximing"

Now showing 1 - 16 of 16
  • Thumbnail Image
    Analysis of Deformation Fixation of Thermally Compressed Scots Pine (Pinus sylvestris L.)
    Li, Lili; Shan, Xiaofei; Luo, Zhiying; Liu, Wenwen; Liu, Jianxia; Yu, Jianfang; Chen, Zhangjing; Wang, Ximing (MDPI, 2024-05-11)
    Heat treatment effectively inhibits the water absorption recovery of compressed wood. To elucidate this phenomenon, we prepared compressed pine and thermally compressed pine (heartwood and sapwood) using the hot pressing method at 160 °C, 180 °C, 200 °C, and 220 °C. The effects of chemical components, swelling stresses, and monosaccharides on modified wood recovery were investigated using regression analyses. Notably, the recovery of both compressed heartwood and sapwood during water absorption declined from 18.89% to 2.66% and from 58.40% to 1.60%, respectively, after heat treatment. Similarly, the swelling stresses of the compressed heartwood and sapwood at 220 °C, respectively, ranged from 0.693 MPa to 0.275 MPa and from 0.783 MPa to 0.330 MPa. These were close to the values of untreated heartwood (0.175 MPa) and sapwood (0.225 MPa). Regression functions indicated that the recovery of compressed wood is chemically dependent on hemicellulose and mechanically related to swelling stress. For monosaccharides, regression functions indicated that modified heartwood recovery primarily relied on mannose, whereas modified sapwood recovery was remarkably affected by mannose and xylose. This confirmed that the pyrolytic monosaccharides in hemicellulose promoted stress relaxation, which induced the deformation fixation of thermally compressed wood.
  • Thumbnail Image
    Competitive Adsorption of Cadmium(II) and Mercury(II) Ions from Aqueous Solutions by Activated Carbon from Xanthoceras sorbifolia Bunge Hull
    Zhang, Xiaotao; Hao, Yinan; Wang, Ximing; Chen, Zhangjing; Li, Chun (Hindawi, 2016-12-19)
    This paper presents low-cost and recyclable activated carbon (XLAC) derived from Xanthoceras sorbifolia Bunge hull for high-efficiency adsorption of Cd(II) and Hg(II) ions in industrial wastewater. XLAC was prepared through H3PO4 activation and was characterized using N2 adsorption-desorption, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDX), and Fourier transform infrared (FTIR) spectroscopy. In single-metal-system adsorption experiments, the maximum adsorption capacities for Cd(II) and Hg(II) obtained under different experimental conditions were 388.7 and 235.6 mg·g−1, respectively. All adsorption equilibrium data fit perfectly with the Langmuir isotherm model. In a binary metal system, competitive studies demonstrated that the presence of Cd(II) significantly decreased the adsorption of Hg(II), but the adsorption of Cd(II) showed a little change in the presence of Hg(II). In addition, XLAC can be regenerated with a 0.01 mol·L−1 HNO3 solution and reused at least four times. The FTIR spectra revealed that a chemical interaction occurs between functional groups containing lone electron pairs in XLAC and metal ions. Overall, these results suggest that XLAC may be suitable as an adsorbent for heavy metal removal from wastewater streams.
  • Thumbnail Image
    Effects of Thermo-Hydro-Mechanical Treatments on Various Physical and Mechanical Properties of Poplar (Populus) Wood
    Shao, Yali; Li, Lili; Chen, Zhangjing; Wang, Sunguo; Wang, Ximing (2020-11)
    Poplar (Populus) wood was subjected in this work to thermo-hydro-mechanical treatment. The influence of the treatment parameters on the physical and mechanical properties were investigated. The wood samples were densified under three compression ratios (0%, 30%, and 50%), and thermally treated at three temperatures (180 degrees C, 200 degrees C, and 220 degrees C), at three thermal treatment durations (3 h, 4 h, and 5 h). The density, modulus of elasticity, modulus of rupture, radial hardness, and thickness swelling were measured. The results showed that the densities of the samples increased by 36.6% to 49.7%. As the compression rate increased, the temperature, duration, modulus of elasticity, modulus of rupture, and hardness increased. However, the dimensions of the densified samples were less stable. Compared to the densified samples, the maximum thickness swelling could be reduced by 74% (from 29.7% to 7.8%) when subjected to a thermal treatment at 220 degrees C for 3 h.
  • Thumbnail Image
    Efficient Adsorption-Assisted Photocatalysis Degradation of Congo Red through Loading ZIF-8 on KI-Doped TiO2
    Liu, Zhechen; Zhang, Wanqi; Zhao, Xilong; Sheng, Xianliang; Hu, Zichu; Wang, Qiang; Chen, Zhangjing; Wang, Sunguo; Zhang, Xiaotao; Wang, Ximing (MDPI, 2022-04-13)
    Zeolitic imidazolate framework-8 (ZIF-8) was evenly loaded on the surface of TiO2 doped with KI, using a solvent synthesis method, in order to produce a ZIF-8@TiO2 (KI) adsorption photocatalyst with good adsorption and photocatalytic properties. The samples were characterized by XRD, SEM, EDX, XPS, BET and UV-Vis. The photocatalytic efficiency of the material was obtained by photocatalytic tests. The results indicate that the doping with I inhibited the grain growth and reduced the crystallite size of TiO2, reduced the band gap width and improved the utilization rate for light. TiO2 (KI) was a single crystal of anatase titanium dioxide. The combination of ZIF-8 and TiO2 (KI) improved the specific surface area and increased the reaction site. The ZIF-8@TiO2 (KI) for Congo red was investigated to validate its photocatalytic performance. The optimal concentration of Congo red solution was 30 mg/L, and the amount of catalyst was proportional to the degradation efficiency. The degradation efficiency of ZIF-8@TiO2 (5%KI) was 76.42%, after being recycled four times.
  • Thumbnail Image
    Enhanced heavy metal removal from an aqueous environment using an eco-friendly and sustainable adsorbent
    Zhang, Wanqi; An, Yuhong; Li, Shujing; Liu, Zhechen; Chen, Zhangjing; Ren, Yukun; Wang, Sunguo; Zhang, Xiaotao; Wang, Ximing (2020-10-05)
    Thiol-lignocellulose sodium bentonite (TLSB) nanocomposites can effectively remove heavy metals from aqueous solutions. TLSB was formed by using-SH group-modified lignocellulose as a raw material, which was intercalated into the interlayers of hierarchical sodium bentonite. Characterization of TLSB was then performed with BET, FTIR, XRD, TGA, PZC, SEM, and TEM analyses. The results indicated that thiol-lignocellulose molecules may have different influences on the physicochemical properties of sodium bentonite, and an intercalated-exfoliated structure was successfully formed. The TLSB nanocomposite was subsequently investigated to validate its adsorption and desorption capacities for the zinc subgroup ions Zn(II), Cd(II) and Hg(II). The optimum adsorption parameters were determined based on the TLSB nanocomposite dosage, concentration of zinc subgroup ions, solution pH, adsorption temperature and adsorption time. The results revealed that the maximum adsorption capacity onto TLSB was 357.29 mg/g for Zn(II), 458.32 mg/g for Cd(II) and 208.12 mg/g for Hg(II). The adsorption kinetics were explained by the pseudo-second-order model, and the adsorption isotherm conformed to the Langmuir model, implying that the dominant chemical adsorption mechanism on TLSB is monolayer coverage. Thermodynamic studies suggested that the adsorption is spontaneous and endothermic. Desorption and regeneration experiments revealed that TLSB could be desorbed with HCl to recover Zn(II) and Cd(II) and with-HNO3 to recover Hg(II) after several consecutive adsorption/desorption cycles. The adsorption mechanism was investigated through FTIR, EDX and SEM, which demonstrated that the introduction of thiol groups improved the adsorption capacity. All of these results suggested that TLSB is an eco-friendly and sustainable adsorbent for the extraction of Zn(II), Cd(II) and Hg(II) ions in aqueous media.
  • Thumbnail Image
    Eu-Doped Zeolitic Imidazolate Framework-8 Modified Mixed-Crystal TiO2 for Efficient Removal of Basic Fuchsin from Effluent
    Zhang, Wanqi; Liu, Hui; Liu, Zhechen; An, Yuhong; Zhong, Yuan; Hu, Zichu; Li, Shujing; Chen, Zhangjing; Wang, Sunguo; Sheng, Xianliang; Zhang, Xiaotao; Wang, Ximing (MDPI, 2021-11-27)
    Zeolitic imidazolate framework-8 (ZIF-8) was doped with a rare-earth metal, Eu, using a solvent synthesis method evenly on the surface of a mixed-crystal TiO2(Mc-TiO2) structure in order to produce a core–shell structure composite ZIF-8(Eu)@Mc-TiO2 adsorption photocatalyst with good adsorption and photocatalytic properties. The characterisation of ZIF-8(Eu)@Mc-TiO2 was performed via X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), Brunauer–Emmett–Teller analysis (BET) and ultraviolet–visible light differential reflectance spectroscopy (UV-DRs). The results indicated that Eu-doped ZIF-8 was formed evenly on the Mc-TiO2 surface, a core–shell structure formed and the light-response range was enhanced greatly. The ZIF-8(Eu)@Mc-TiO2 for basic fuchsin was investigated to validate its photocatalytic performance. The effect of the Eu doping amount, basic fuchsin concentration and photocatalyst dosage on the photocatalytic efficiency were investigated. The results revealed that, when 5%-Eu-doped ZIF-8(Eu)@Mc-TiO2 (20 mg) was combined with 30 mg/L basic fuchsin (100 mL) under UV irradiation for 1 h, the photocatalytic efficiency could reach 99%. Further, it exhibited a good recycling performance. Thus, it shows certain advantages in its degradation rate and repeatability compared with previously reported materials. All of these factors suggested that, in an aqueous medium, ZIF-8(Eu)@Mc-TiO2 is an eco-friendly, sustainable and efficient material for the photocatalytic degradation of basic fuchsin.
  • Thumbnail Image
    Evaluation of Aerogel Spheres Derived from Salix psammophila in Removal of Heavy Metal Ions in Aqueous Solution
    Zhong, Yuan; An, Yuhong; Wang, Kebing; Zhang, Wanqi; Hu, Zichu; Chen, Zhangjing; Wang, Sunguo; Wang, Boyun; Wang, Xiao; Li, Xinran; Zhang, Xiaotao; Wang, Ximing (MDPI, 2022-01-04)
    Heavy metal wastewater treatment is a huge problem facing human beings, and the application degree of Salix psammophila resources produced by flat stubble is low. Therefore, it is very important to develop high-value products of Salix psammophila resources and apply them in the removal heavy metal from effluent. In this work, we extracted the cellulose from Salix psammophila, and cellulose nanofibers (CNFs) were prepared through TEMPO oxidation/ultrasound. The aerogel spheres derived from Salix psammophila (ASSP) were prepared with the hanging drop method. The experimental results showed that the Cu(II) adsorption capacity of the ASSP composite (267.64 mg/g) doped with TOCNF was significantly higher than that of pure cellulose aerogel spheres (52.75 mg/g). The presence of carboxyl and hydroxyl groups in ASSP enhanced the adsorption capacity of heavy metals. ASSP is an excellent heavy metal adsorbent, and its maximum adsorption values for Cu(II), Mn(II), and Zn(II) were found to be 272.69, 253.25, and 143.00 mg/g, respectively. The abandoned sand shrub resource of SP was used to adsorb heavy metals from effluent, which provides an important reference value for the development of forestry in this sandy area and will have a great application potential in the fields of the adsorption of heavy metals in soil and antibiotics in water.
  • Thumbnail Image
    The Influence of a Thermal Treatment on the Decay Resistance of Wood via FTIR Analysis
    Hao, Yinan; Pan, Yanfei; Du, Rui; Wang, Yamei; Chen, Zhangjing; Zhang, Xiaotao; Wang, Ximing (Hindawi, 2018-01-28)
    The decay resistance of wood can be improved via a vacuum heat treatment. The amount of nutrients from cellulose, hemicellulose, and lignin and amount of sugars needed by the fungi during their growth were investigated. The results showed that the absorbance peaks corresponding to absorbed CH3-CH2-, C=O, and the benzene ring skeleton stretching vibration all noticeably weakened with increased heat treatment. This indicated that the cellulose, hemicellulose, and lignin degraded to varying degrees. The specimens with a higher initial moisture content (MC) showed greater amounts of nutrient degradation after 2 h at the same heat treatment temperature. The chemical analysis results were in good agreement with the Fourier transform infrared (FTIR) analysis results. The decay resistance tests showed that the average mass loss of the heat-treated specimens was up to 10.8%, in contrast to 22.23% for the untreated specimens. Furthermore, the FTIR analysis of the heat and decay-resistance test showed that the vibration wave peaks that corresponded to CH3-CH2- at 2954 cm−1 showed noticeably less separation at higher heating temperature. This demonstrated that the cellulose hydrolysis in the wood decreased at higher heating temperatures, which explained why the decay resistance increased with increased heat treatment.
  • Thumbnail Image
    Lignocellulose-Based Superabsorbent Polymer Gel Crosslinked with Magnesium Aluminum Silicate for Highly Removal of Zn (II) from Aqueous Solution
    An, Yuhong; Zhang, Wanqi; Liu, Hui; Zhong, Yuan; Hu, Zichu; Shao, Yali; Chen, Zhangjing; Ren, Yukun; Wang, Boyun; Wang, Sunguo; Zhang, Xiaotao; Wang, Ximing (MDPI, 2021-11-28)
    Lignocellulose (LCE) was ultrasonically treated and intercalated into magnesium aluminum silicate (MOT) clay to prepare a nano-lignocellulose magnesium aluminum silicate polymer gel (nano-LCE-MOT) for the removal of Zn (II) from aqueous solution. The product was characterised using nitrogen adsorption/desorption isotherm measurements, Fourier-transform infrared spectroscopy, scanning electron microscopy and energy-dispersive X-ray spectroscopy. The conditions for the adsorption of Zn (II) on nano-LCE-MOT were screened, and adsorption kinetics and isotherm model analysis were carried out to explore the adsorption mechanism and achieve the optimal adsorption of Zn (II). Optimal adsorption was achieved at an initial Zn (II) concentration of 800 mg/L at 60 °C in 160 min at a pH of 4.52. The adsorption kinetics were explored using a pseudo-second-order model, with the isotherm adsorption equilibrium found to conform to the Langmuir model. The maximum adsorption capacity of the nano-LCE-MOT polymer gel toward Zn (II) is 513.48 mg/g. The materials with adsorbed Zn (II) were desorbed using different media, with HCl found to be the most ideal medium to desorb Zn (II). The optimal desorption of Zn (II) was achieved in 0.08 mol/L HCl solution at 65 °C in 60 min. Under these conditions, Zn (II) was almost completely desorbed from the adsorbents, with the adsorption effect after cycling being slightly different from that of the initial adsorption.
  • Thumbnail Image
    Lignocellulose@ Activated Clay Nanocomposite with Hierarchical Nanostructure Enhancing the Removal of Aqueous Zn(II)
    Zhang, Xiaotao; Hao, Yinan; Chen, Zhangjing; An, Yuhong; Zhang, Wanqi; Wang, Ximing (MDPI, 2019-10-18)
    A lignocellulose@ activated clay (Ln@AC) nanocomposite with a hierarchical nanostructure was successfully synthesized by the chemical intercalation reaction and applied in the removal of Zn(II) from an aqueous solution. Ln@AC was characterized by N2 adsorption/desorption isotherms and X-Ray Diffraction (XRD), scanning Electron Microscope (SEM), transmission Electron Microscopy (TEM) and Fourier Transform Infrared Spectroscopy (FTIR) analysis, and the results indicate that an intercalated–exfoliated hierarchical nanostructure was formed. The effects of different adsorption parameters on the Zn(II) removal rate (weight ratio of Ln to AC, Ln@AC dosage, initial Zn(II) concentration, pH value, adsorption temperature, and time) were investigated in detail. The equilibrium adsorption capacity reached 315.9 mg/g under optimal conditions (i.e., the weight ratio of Ln to AC of 3:1, Ln@AC dosage of 1 g/L, initial Zn(II) concentration of 600 mg/L, pH value of 6.8, adsorption temperature of 65 °C, and adsorption time of 50 min). The adsorption process was described by the pseudo-second-order kinetic model, Langmuir isotherm model, and the Elovich model. Moreover, Zn(II) could be easily eluted by HCl, and the effects of HCl concentration, desorption temperature, and ultrasonic desorption time on desorbed amount were tested. Desorption studies revealed that with an HCl concentration of 0.25 mol/L, desorption temperature of 70 °C, and ultrasonic desorption time of 20 min, the maximum desorption capacity and efficiency were achieved at 202.5 mg/g and 64.10%, respectively. Regeneration experimental results indicated that the Ln@AC exhibited a certain recyclable regeneration performance. Due to such outstanding features, the novel Ln@AC nanocomposite proved to have great adsorption potential for Zn(II) removal from wastewater, and exhibited an extremely significant amount of adsorbed Zn(II) when compared to conventional adsorbents.
  • Thumbnail Image
    Nano@lignocellulose intercalated montmorillonite as adsorbent for effective Mn(II) removal from aqueous solution
    An, Yuhong; Zhang, Xiaotao; Wang, Ximing; Chen, Zhangjing; Wu, Xiangwen (Springer Nature, 2018-07-18)
    This paper describes the preparation of nano@lignocellulose (nano@LC) and a nano@lignocellulose/montmorillonite (nano@LC/MT) nanocomposite, as well as the capacity of the nano@LC/MT for adsorbing manganese ions from aqueous solution. The structure of nano@LC and nano@LC/MT was characterised by Fourier-transform infrared spectroscopy, X-ray diffraction, Scanning electron microscopy, and Transmission electron microscopy, which revealed that the diffraction peak of montmorillonite almost disappeared, infrared bands of the functional groups shifted, and morphology of the material changed after the formation of the composite. The optimum conditions for the adsorption of Mn(II) on the nano@LC/MT nanocomposite were investigated in detail by changing the initial Mn(II) concentration, pH, adsorption temperature, and time. The results revealed that the adsorption capacity of the nano@LC/MT nanocomposite for Mn(II) reached 628.0503 mg/g at a Mn(II) initial concentration of 900 mg/L, solution pH 5.8, adsorption temperature 55 degrees C, and adsorption time 160 min. Adsorption kinetics experiments revealed good agreement between the experimental data and the pseudo-second order kinetic model. The experimental data was satisfactorily fitted to the Langmuir isotherm. Adsorption-desorption results showed that nano@LC/MT exhibited excellent reusability. The adsorption mechanism was investigated through FT-IR and EDX spectroscopic analyses. The results suggested that nano@LC/MT have great potential in removing Mn(II) from water.
  • Thumbnail Image
    A Novel Nanocomposite as an Efficient Adsorbent for the Rapid Adsorption of Ni(II) from Aqueous Solution
    Zhang, Xiaotao; Wang, Ximing; Chen, Zhangjing (MDPI, 2017-09-22)
    A sulfhydryl-lignocellulose/montmorillonite (SLT) nanocomposite was prepared using a chemical intercalation reaction. The SLT nanocomposite was characterized by Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XRD), Scanning Electron Microscope (SEM), and Transmission Electron Microscopy (TEM), the results demonstrated that an intercalated-exfoliated nanostructure was formed in the SLT nanocomposite. Batch experiments were conducted to optimize parameters such as SLT nanocomposite dosage, the initial concentration of Ni(II), solution pH, temperature, and time. The results indicated that the attractive adsorption capacity reached 1134.08 mg/g with 0.05 g of SLT at an initial concentration of Ni(II) of 700 mg/L, solution pH of 5.5, adsorption temperature of 50 °C, and adsorption time of 40 min, meanwhile, the Ni(II) adsorption capacity significantly decreased with the increase in ionic strength. The pseudo-second order kinetic model could describe the whole adsorption process well, and the isotherm adsorption equilibrium conformed to the Freundlich model. The adsorption mechanism of SLT was also discussed by means of FTIR and Energy-Dispersive X-Ray (EDX). Dramatically, the introduction of sulfhydryl achieves the increased activated functional groups content of SLT nanocomposite, leading to remarkably higher adsorption amount on Ni(II). The desorption capacity of SLT was dependent on parameters such as HNO3 concentration, desorption temperature, and ultrasonic desorption time. The satisfactory desorption capacity and desorption efficiency of 458.21 mg/g and 40.40% were obtained at an HNO3 concentration, desorption temperature, and ultrasonic desorption time of 0.4 mol/L, 40 °C, and 30 min, respectively. The regeneration studies showed that the adsorption capacity of SLT was consistent for four cycles without any appreciable loss and confirmed that the SLT was reusable. Owing to such outstanding features, the novel SLT nanocomposite proved the great potential in adsorption for Ni(II) removal from aqueous solution, and exhibited an extremely significant amount of Ni(II), compared to pristine lignocellulose/montmorillonite and the conventional spent adsorbents.
  • Thumbnail Image
    Radioactive Cobalt(II) Removal from Aqueous Solutions Using a Reusable Nanocomposite: Kinetic, Isotherms, and Mechanistic Study
    Zhang, Xiaotao; Wang, Ximing; Chen, Zhangjing (MDPI, 2017-11-24)
    A lignocellulose/montmorillonite (LMT) nanocomposite was prepared as a reusable adsorbent for cobalt(II) ions, and characterized by nitrogen (N2) adsorption/desorption isotherm, X-ray Diffraction (XRD), Scanning Electron Microscope (SEM), Transmission Electron Microscopy (TEM), and Fourier Transform Infrared Spectroscopy (FTIR). LMT exhibited efficient adsorption of cobalt ions (Co(II)), and the adsorbed Co(II) was readily desorbed by nitric acid (HNO3). All parameters affecting the adsorption and/or desorption of Co(II), including initial Co(II) concentration, pH value, temperature, HNO3 concentration, and time, were optimized. The kinetic data analysis showed that the adsorption followed the pseudo-second-order kinetic model and fit well into the Langmuir isotherm equation. Notably, the nanocomposite can be used four times without significantly losing adsorbent capability. The Energy-Dispersive X-ray (EDX) and FTIR spectra analysis also revealed that the adsorption mechanism may be mainly a chemical adsorption dominated process.
  • Thumbnail Image
    Rapid Removal of Zinc(II) from Aqueous Solutions Using a Mesoporous Activated Carbon Prepared from Agricultural Waste
    Zhang, Xiaotao; Hao, Yinan; Wang, Ximing; Chen, Zhangjing (MDPI, 2017-08-28)
    A low-cost activated carbon (XSBLAC) prepared from Xanthoceras Sorbifolia Bunge hull via chemical activation was investigated to determine its adsorption and desorption properties for zinc(II) ions from aqueous solutions. XSBLAC was characterized based on its N2-adsorption/desorption isotherm, EDX, XRD, SEM and FTIR results. An adsorption study was conducted in a series of experiments to optimize the process variables for zinc(II) removal using XSBLAC. Modeling the adsorption kinetics indicated good agreement between the experimental data and the pseudo-second-order kinetic model. The Langmuir equilibrium isotherm fit the experimental data reasonably well. The calculated enthalpy (ΔH0), entropy (ΔS0) and Gibbs free energy (ΔG0) values revealed the endothermic and spontaneous nature of the adsorption process. HNO3 displayed the best desorption performance. The adsorption mechanism was investigated in detail through FTIR and SEM/EDX spectroscopic analyses. The results suggested that XSBLAC is a potential biosorbent for removing zinc(II) from aqueous solutions.
  • Thumbnail Image
    Study of VOCs release during drying of plantation-grown Pinus sylvestris and naturally grown Russian Pinus sylvestris
    Shen, Yulin; Zhang, Xiaotao; He, Qin; Wang, Xia; Wang, Zhe; Yang, Junli; Chen, Zhangjing; Yu, Jianfang; Duo, Huaqiong; Wang, Ximing (2020-05-12)
    A study was carried out to investigate the release of volatile organic compounds (VOCs) during drying of plantation Pinus sylvestris grown in China and naturally grown Pinus sylvestris from Russia. Our purpose was to provide basic information that can help wood processing mills set their VOCs emission limits and control the exhaust gas within such limits. During conventional drying of the plantation Pinus sylvestris, a total of 22 chemical compounds were detected in the exhaust gas: 9 aldehydes including formaldehyde, 8 terpenes including α-pinene, and 3 additional compounds including alkane, and propylbenzene. The VOCs released during both conventional drying and high-temperature drying were the same. However, large amounts of benzene were detected during the high-temperature drying process. During conventional drying of the Russian Pinus sylvestris material, a total of 17 chemical compounds were detected: 7 aldehydes including formaldehyde, 6 terpenes including α-pinene, and 2 additional compounds. The VOCs released during conventional drying and high-temperature drying were the same. However, large amounts of camphene were detected during high-temperature drying. For plantation Pinus sylvestris, the release of VOCs primarily took place at the later stage of conventional drying, and at the earlier stage of high-temperature drying. For Russian Pinus sylvestris, the amount and the release rate of VOCs during conventional drying were extremely low, and the VOCs during high-temperature drying were primarily released at the later stage. The total amount of VOCs released during drying was much higher from the plantation Pinus sylvestris than from Russian Pinus sylvestris material.
  • Thumbnail Image
    Wood for Application in Electrochemical Energy Storage Devices
    Shan, Xiaofei; Wu, Jing; Zhang, Xiaotao; Wang, Li; Yang, Junli; Chen, Zhangjing; Yu, Jianfang; Wang, Ximing (Elsevier, 2021-12-22)
    Nowadays, achieving powerful electrochemical energy conversion and storage devices is a major challenge of our society. Wood is a biodegradable and renewable material that naturally has a hierarchical porous structure, excellent mechanical performance, and versatile physicochemical properties. Wood-based materials and its derivatives are endowed with great potential as resources to fabricate advanced materials for energy storage, flexible electronics, and clean energy. Herein, we comprehensively overview the methodologies applied for the synthesis of various electrochemical energy storage systems and devices (e.g., supercapacitor, battery, catalytic hydrogen evolution, etc.), the strategies for tailoring the structures and conductivity, as well as their impact on electrochemical performance (energy and power density and long-term durability). Finally, an outlook of future opportunities and prospects in the synthesis and application of electrochemical energy storage is also presented.