VTechWorks Repository :: Browsing by Author "Whittington, Abby R."

Browsing by Author "Whittington, Abby R."

Now showing 1 - 20 of 42

Advancing Step-Growth Polymers: Novel Macromolecular Design and Electrostatic Interactions in Polyesters and Polyurethanes
Zhang, Musan (Virginia Tech, 2013-06-17)
Conventional melt transesterification successfully synthesized high molecular weight segmented copolyesters. The cycloaliphatic monomers 2,2,4,4-tetramethyl-1,3-cyclobutanediol (CBDO) and dimethyl-1,4-cyclohexane dicarboxylate (DMCD) afforded sterically hindered, ester carbonyls in high-Tg polyester precursors. Reaction between the polyester polyol precursor and a primary or secondary alcohol at melt polymerization temperatures revealed reduced transesterification of the polyester hard segment as a result of enhanced steric hindrance adjacent to the ester linkages. Subsequent polymerization of a 4,000 g/mol polyol with monomers comprising the low-Tg block yielded high molecular weight polymers that exhibited enhanced mechanical properties compared to a non-segmented copolyester control. Atomic force microscopy uncovered unique needle-like, interconnected, microphase separated surface morphologies, and small-angle X-ray scattering confirmed the presence of bulk microphase separation. This new synthetic strategy enabled selective control of ionic charge placement into the hard segment or soft segment block of segmented copolyesters using melt transesterification. The ionic placement impacted the microphase-separated morphology, which influenced its thermomechanical properties and resulting mechanical performance. Melt transesterification of low-Tg, sodium sulfonated copolyesters achieved up to 15 mol% ionic content. The 10 and 15 mol% sodium sulfonated copolyesters exhibited water-dispersibility, which enabled cation dialysis exchanges to divalent metal cations. The sulfonated copolyesters containing divalent metal cations exhibited enhanced rubbery plateau moduli to higher temperatures. Novel trialkylphosphonium ionic liquids chain extenders enabled the successful synthesis of poly(ethylene glycol)-based, cationic polyurethanes with pendant phosphoniums in the hard segments (HS). Aqueous size exclusion chromatography (SEC) confirmed the charged polyurethanes, which varied the phosphonium alkyl substituent length (ethyl and butyl) and cationic HS content (25, 50, 75 mol%), achieved high absolute molecular weights. Dynamic mechanical analysis (DMA) demonstrated the triethylphosphonium (TEP) and tributylphosphonium (TBP) polyurethanes displayed similar thermomechanical properties, including increased rubbery plateau moduli and flow temperatures. Fourier transform infrared spectroscopy (FTIR) emphasized the significance of ion-dipole interaction on hydrogen bonding. Atomic force microscopy (AFM), small-angle X-ray scattering (SAXS), and wide-angle X-ray diffraction (WAXD) supported microphase separated morphologies in the trialkylphosphonium polyurethanes, despite the presence of ionic interactions. Sorption isotherm experiments revealed TBP polyurethanes displayed similar water sorption profiles to the noncharged analogue and lower water absorptivity compared to TEP. The phosphonium polyurethanes displayed significantly improved tensile strain; however, lower tensile stress of the TEP polyurethane was presumably due to absorbed water. In addition, we also explored applications of the trialkylphosphonium polyurethanes as nucleic acid delivery vectors and demonstrated their abilities to form colloidally stable polyplexes in salt-containing media.
Alternative strategies to incorporate biomolecules within electrospun meshes for tissue enginering
Vaidya, Prasad Avdhut (Virginia Tech, 2014-10-15)
Rupture of the anterior cruciate ligament (ACL) is one of the most common ligamentous injuries of the knee. Post rupture, the ACL does not heal on itself due to poor vasculature and hence surgical intervention is required to treat the ACL. Current surgical management of ACL rupture consists of reconstruction with autografts or allografts. However, the limitations associated with these grafts have prompted interest in tissue engineered solutions that combine cells, scaffolds and stimuli to facilitate ACL regeneration. This thesis describes a ligament tissue engineering strategy that involves incorporating biomolecules within fibers-based electrospun meshes which mimics the extra-cellular matrix microarchitecture of ligament. However, challenges exist with incorporation of biomolecules. Therefore, the goal of this research project was to develop two techniques to incorporate biomolecules within electrospun meshes: (1) co-axially electrospinning fibers that support surface-grafting of biomolecules, and (2) co-axially electrospinning fibers decorated with biomolecule-loaded microspheres. In the first approach, chitosan was co-axially electrospun on the shell side of poly caprolactone (PCL) and arginine-glycine-aspartate (RGD) was attached to the electrospun meshes. Bone marrow stromal cells (BMSCs) attached, spread and proliferated on these meshes. In the second approach, fluorescein isothiocyanate labelled bovine serum albumin (FITC-BSA) loaded chitosan-alginate (CS-AL) microspheres were fabricated. The effects of cation to alginate ratio, type of alginate and concentration of CaCl2 on microsphere size, FITC-BSA loading and release were systematically evaluated. The CS-AL microspheres were then incorporated into the sheath phase of co-axially electrospun meshes to achieve microsphere-decorated fiber composite meshes. The results from these model study suggest that both approaches are tractable for incorporating biomolecules within fibers-based electrospun meshes. Both these approaches provide platform for future studies that can focus on ligament-relevant biomolecules such as FGF-2 and GDF-5.
Biaxial Mechanical Evaluation of Uterosacral and Cardinal Ligaments
Baah-Dwomoh, Adwoa Sarpong (Virginia Tech, 2018-03-06)
The uterosacral ligament (USL) and the cardinal ligament (CL) are two major suspensory tissues that provide structural support to the vagina/cervix/uterus complex. These ligaments have been studied mainly due for their role in the surgical repair for pelvic organ prolapse (POP). POP, which is the descent of a pelvic organ from its normal place towards the vaginal walls and into the vaginal cavity, affects an estimated 3.3 million women in the United States annually. Despite their important mechanical function, little is known about the elastic and viscoelastic properties of the USL and CL due to ethical concerns with in vivo testing of human tissues and the lack of accepted animal models. The goal of this first study is to help establish an appropriate animal model for studying the mechanics of these pelvic supportive ligaments. To achieve this, the first rigorous comparison of histological and planar equi-biaxial mechanical properties of the swine and human USLs was completed. Relative collagen, smooth muscle, and elastin contents were quantified from histological sections and the USL was found to have similar components in both species, with a comparable relative collagen content. Using the digital image correlation (DIC) method to calculate the in-plane Lagrangian strain, no differences in the peak strain during precon- ditioning/cyclic loading tests, secant modulus of the pre-creep/elastic response, and strain at the end of creep tests were detected in the USLs from the two species along both axial loading directions (the main in vivo loading direction and the direction that is perpendicular to it). Because these ligaments are subjected to repeated constant loads in vivo, the effect of re- peated biaxial loads at three different load levels (1 N, 2 N, or 3 N) on elastic and creep properties of the swine CL was investigated. The results showed that CL was elastically anisotropic, as statistical differences were found between the mean strains along the two axial loading directions for specimens at all three different load levels. The increase in strain over time by the end of the 3rd creep test was comparable along the axial loading direc- tions. The greatest mean normalized strain (or, equivalently, the largest increase in strain over time) was measured at the end of the 1st creep test, regardless of the equi-biaxial load magnitude or loading direction. Overall, these experimental findings validate the use of swine as an appropriate animal model and offer new knowledge of the mechanical properties of the USL and CL that can guide the development of better treatment methods such as surgical reconstruction for POP.
Bioactive Cellulose Nanocrystal Reinforced 3D Printable Poly(epsilon-caprolactone) Nanocomposite for Bone Tissue Engineering
Hong, Jung Ki (Virginia Tech, 2015-05-07)
Polymeric bone scaffolds are a promising tissue engineering approach for the repair of critical-size bone defects. Porous three-dimensional (3D) scaffolds play an essential role as templates to guide new tissue formation. However, there are critical challenges arising from the poor mechanical properties and low bioactivity of bioresorbable polymers, such as poly(epsilon-caprolactone) (PCL) in bone tissue engineering applications. This research investigates the potential use of cellulose nanocrystals (CNCs) as multi-functional additives that enhance the mechanical properties and increase the biomineralization rate of PCL. To this end, an in vitro biomineralization study of both sulfuric acid hydrolyzed-CNCs (SH-CNCs) and surface oxidized-CNCs (SO-CNCs) has been performed in simulated body fluid in order to evaluate the bioactivity of the surface functional groups, sulfate and carboxyl groups, respectively. PCL nanocomposites were prepared with different SO-CNC contents and the chemical/physical properties of the nanocomposites were analyzed. 3D porous scaffolds with fully interconnected pores and well-controlled pore sizes were fabricated from the PCL nanocomposites with a 3D printer. The mechanical stability of the scaffolds were studied using creep test under dry and submersion conditions. Lastly, the biocompatibility of CNCs and 3D printed porous scaffolds were assessed in vitro. The carboxyl groups on the surface of SO-CNCs provided a significantly improved calcium ion binding ability which could play an important role in the biomineralization (bioactivity) by induction of mineral formation for bone tissue engineering applications. In addition, the mechanical properties of porous PCL nanocomposite scaffolds were pronouncedly reinforced by incorporation of SO-CNCs. Both the compressive modulus and creep resistance of the PCL scaffolds were enhanced either in dry or in submersion conditions at 37 degrees Celsius. Lastly, the biocompatibility study demonstrated that both the CNCs and material fabrication processes (e.g., PCL nanocomposites and 3D printing) were not toxic to the preosteoblasts (MC3T3 cells). Also, the SO-CNCs showed a positive effect on biomineralization of PCL scaffolds (i.e., accelerated calcium or mineral deposits on the surface of the scaffolds) during in vitro study. Overall, the SO-CNCs could play a critical role in the development of scaffold materials as a potential candidate for reinforcing nanofillers in bone tissue engineering applications.
Bioactive Cellulose Nanocrystal-Poly(epsilon-Caprolactone) Nanocomposites for Bone Tissue Engineering Applications
Hong, Jung Ki; Cooke, Shelley L.; Whittington, Abby R.; Roman, Maren (2021-02-25)
3D-printed bone scaffolds hold great promise for the individualized treatment of critical-size bone defects. Among the resorbable polymers available for use as 3D-printable scaffold materials, poly(epsilon-caprolactone) (PCL) has many benefits. However, its relatively low stiffness and lack of bioactivity limit its use in load-bearing bone scaffolds. This study tests the hypothesis that surface-oxidized cellulose nanocrystals (SO-CNCs), decorated with carboxyl groups, can act as multi-functional scaffold additives that (1) improve the mechanical properties of PCL and (2) induce biomineral formation upon PCL resorption. To this end, an in vitro biomineralization study was performed to assess the ability of SO-CNCs to induce the formation of calcium phosphate minerals. In addition, PCL nanocomposites containing different amounts of SO-CNCs (1, 2, 3, 5, and 10 wt%) were prepared using melt compounding extrusion and characterized in terms of Young's modulus, ultimate tensile strength, crystallinity, thermal transitions, and water contact angle. Neither sulfuric acid-hydrolyzed CNCs (SH-CNCs) nor SO-CNCs were toxic to MC3T3 preosteoblasts during a 24 h exposure at concentrations ranging from 0.25 to 3.0 mg/mL. SO-CNCs were more effective at inducing mineral formation than SH-CNCs in simulated body fluid (1x). An SO-CNC content of 10 wt% in the PCL matrix caused a more than 2-fold increase in Young's modulus (stiffness) and a more than 60% increase in ultimate tensile strength. The matrix glass transition and melting temperatures were not affected by the SO-CNCs but the crystallization temperature increased by about 5.5 degrees C upon addition of 10 wt% SO-CNCs, the matrix crystallinity decreased from about 43 to about 40%, and the water contact angle decreased from 87 to 82.6 degrees. The abilities of SO-CNCs to induce calcium phosphate mineral formation and increase the Young's modulus of PCL render them attractive for applications as multi-functional nanoscale additives in PCL-based bone scaffolds.
Characterization and Pharmacokinetics of Rifampicin Laden Carboxymethylcellulose Acetate Butyrate Particles
Casterlow, Samantha Alexandra (Virginia Tech, 2012-04-24)
Tuberculosis, caused by Mycobacterium tuberculosis (MTB), is a common and potentially lethal infectious human disease. Rifampicin is a front line anti-tuberculosis drug usually prescribed in combination with isoniazid, pyrazinamide and streptomycin for a period of six to seven months. When given orally for the treatment of MTB, rifampicin exhibits low bioavailability. Recent attempts to increase bioavailability and decrease dosage of anti-tuberculosis drugs have focused on creating polymer coated rifampicin nanoparticles. The research effort presented in this thesis evaluates the formation, characterization and relative bioavailability of rifampicin loaded carboxymethylcellulose acetate butyrate (CMCAB) particles using two different formulation techniques. Multi inlet vortex mixer (MIVM) and manual spray drying techniques were used to form the rifampicin containing CMCAB particles. Characterization studies and analyses of particles revealed differences in particle sizes, shapes and drug loading between the different particle formulation techniques. In vivo pharmacokinetic studies in BALB/c mice indicate that a single dose of rifampicin laden CMCAB spray dried particle formulations are able to improve pharmacokinetic parameters including relative bioavailability of rifampicin compared to that of the free drug form at the same concentration.
Complementary strategies to promote the regeneration of bone-ligament transitions using graded electrospun scaffolds
Samavedi, Satyavrata (Virginia Tech, 2013-05-03)
Grafts currently used for the repair of anterior cruciate ligament (ACL) ruptures integrate poorly with bone due to a significant mismatch in properties between graft and bone. Specifically, conventional grafts (e.g., hamstring tendon) are unable to recapitulate intricate gradients in mechano-chemical properties and extracellular matrix (ECM) architecture found at natural bone-ligament (B-L) transitions, and thus result in stress-concentrations at the graft-bone interface leading to graft failure. In contrast, tissue-engineered scaffolds possessing gradients in properties can potentially guide the establishment of phenotypic gradients in bone marrow stromal cells (BMSCs), and thus aid the regeneration of B-L transitions in the long-term. Towards the eventual goal of regenerating complex tissue transitions, this project employs three complementary strategies to fabricate graded scaffolds. The three strategies involve the presentation of gradients in 1) mineral content, 2) scaffold architecture and 3) growth factor (GF) concentration within scaffolds to control BMSC morphology and phenotype. The first strategy involved co-electrospinning two polymers (one doped with hydroxyapatite) from offset spinnerets onto a rotating drum to produce scaffolds possessing a gradient in mineral content. Post-electrospinning, these graded scaffolds were treated with a simulated body fluid to further enhance the gradient. Analysis of mRNA expression of osteoblastic makers by BMSCs and the deposition of bone-specific ECM proteins indicated that the scaffolds could guide the formation of an osteoblastic phenotypic gradient. The second strategy involved electrospinning two polymer solutions onto a custom-designed dual-drum collector to fabricate scaffolds possessing region-wise differences in fiber alignment, diameter and chemistry. Specifically, electrospinning onto the dual-drum collector resulted in the deposition of aligned fibers from one polymer solution in the gap region between the drums, randomly oriented fibers from the other polymer solution on one of the drums and a mixture of fibers from both polymer solutions in the overlap region in between. The topographical cues within these scaffolds were shown to result in region-dependent BMSC morphology and orientation. Although the long-term goal of the third strategy was to create a co-electrospun scaffold possessing a gradient in GF concentration, a new technique to protect GF activity within electrospun scaffolds via the use of gelatin microspheres was first validated. Preliminary results from these studies indicate that microspheres can protect and deliver a model protein (lysozyme) in active conformation from electrospun scaffolds. These results further suggest that gradients of GF concentration can be achieved in the long-term by protecting GFs within microspheres and co-electrospinning as described in the first strategy. In conclusion, the results from this project suggest that graded scaffolds can help guide the formation of gradients in cell morphology, orientation and phenotype, and thus potentially promote the regeneration of B-L transitions in the long-term. The three strategies described in this project can be employed in concert to create scaffolds intended for the regeneration of complex tissue transitions.
Creation and Characterization of Several Polymer/Conductive Element Composite Scaffolds for Skeletal Muscle Tissue Engineering
Fischer, Kristin Mckeon (Virginia Tech, 2012-02-17)
After skeletal muscle damage, satellite cells move towards the injured area to assist in regeneration. However, these cells are rare as their numbers depend on the age and composition of the injured muscle. This regeneration method often results in scar tissue formation along with loss of function. Although several treatment methods have been investigated, no muscle replacement treatment currently exists. Tissue engineering attempts to create, repair, and/or replace damaged tissue by combining cells, biomaterials, and tissue-inducing substances such as growth factors. Electrospinning produces a non-woven scaffold out of biomaterials with fiber diameters ranging from nanometers to microns to create an extracellular-like matrix on which cells attach and proliferate. Our focus is on synthetic polymers, specifically poly(D,L-lactide) (PDLA), poly(L-lactide) (PLLA), and poly(ε-caprolactone) (PCL). Skeletal muscle cells grown on electrospun scaffolds tend to elongate and fuse together thus, mimicking natural tissue. Electrical stimulation has been shown to increase the number of cells fused in culture and decreased the time needed in culture for cells to contract. Therefore, a conductive element was added to each scaffold, specifically polyaniline (PANi), gold nanoparticles (Au Nps), and multi-walled carbon nanotubes (MWCNT). Our project goal is to create a polymeric, conductive, and biocompatible scaffold for skeletal muscle regeneration. PANi and PDLA were mixed to form the following solutions 24% (83% PDLA/17% PANi), 24% (80% PDLA/20% PANi), 22% (75%PDLA/25% PANi), 29% (83% PDLA/17% PANi), and 29% (80% PDLA/20% PANi). Only the 75/25 electrospun scaffold was conductive and had a calculated conductivity of 0.0437 S/cm. Scaffolds with larger amounts of PANi were unable to be electrospun. PDLA/PANi scaffolds were biocompatible as primary rat skeletal muscle cells cultured in vitro did attach. However, the scaffolds shrunk, degraded easily, and became brittle. Although PDLA/PANi scaffolds were easily manufactured, our results indicate that this polymer mixture is not appropriate for skeletal muscle scaffolds. PLLA and Au Nps were electrospun together to form three composite scaffolds: 7% Au-PLLA, 13% Au-PLLA, and 21% Au-PLLA. These were compared to PLLA electrospun scaffolds. Measured scaffold conductivities were 0.008 ± 0.015 S/cm for PLLA, 0.053 ± 0.015 S/cm for 7% Au-PLLA, 0.076 ± 0.004 S/cm for 13% Au-PLLA, and 0.094 ± 0.037 S/cm for 21% Au-PLLA. It was determined via SEM with a Bruker energy dispersive x-ray spectrometer (EDS) that the Au Nps were not evenly distributed within the scaffolds as they had agglomerated. Rat primary muscle cells cultured on the three Au-PLLA scaffolds displayed low cellular activity. A second cell study was conducted to determine Au NPs toxicity. The results show that the Au Nps were not toxic to the cells and the low cellular activity may be a marker for myotube fusion. Elastic modulus and yield stress values for the three Au-PLLA scaffolds measured on days 0, 7, 14, 21, and 28 were much larger than skeletal muscle tissue. Due to the larger mechanical properties and Au Nps agglomeration, a third polymer and conductive element scaffold was investigated. PCL was chosen as the new synthetic polymer as it had a lower elastic modulus and high elongation. MWCNT were chosen as the conductive element as they disperse well within PCL when acid functionalized. A third component was added to the scaffold to help it move similar to skeletal muscle. Ionic polymer gels (IPG) are hydrogels that respond to an external stimulus such as temperature, pH, light, and electric field. A poly(acrylic acid)/poly(vinyl alcohol) (PAA/PVA) mixture is one type of IGP that responds to an electric field. The scaffolds were coaxially electrospun so that each fiber had a PCL-MWCNT interior with a PAA/PVA sheath. These scaffolds were compared to electrospun PCL and PCL-MWCNT ones. The addition of MWCNT to the PCL did increase scaffold conductivity. Actuation of the PCL-MWCNT-PAA/PVA scaffold occurred when 15V and 20V were applied. All three scaffolds had rat primary skeletal muscle cells attached but, more multinucleated cells with actin interaction were seen on PCL-MWCNT-PAA/PVA scaffolds. Once again the mechanical properties were greater than muscle, but because of its ability to actuate we believe the PCL-MWCNT-PAA/PVA scaffold has potential as a bioartificial muscle. Further characterization of the PCL-MWCNT-PAA/PVA included varying the ratios of PAA/PVA, smaller crosslinking times, and lower amounts of MWCNT. Four ratios, 83/17, 60/40, 50/50, and 40/60, were successfully coaxially electrospun with PCL and MWCNT. Overall, very few differences were seen between the four ratios in conductivity, cellular biocompatibility, actuation angular speed, and mechanical properties. The 83/17 and 40/60 ratios were chosen for additional investigation into mechanical properties and actuation. As the mechanical properties of the two types of scaffolds did not change significantly through degradation, lower PVA crosslinking times were tested. No significant effects were found and it was hypothesized that the evaporation of the solution played a role in the crosslinking process. The smaller MWCNT amount scaffolds also did not significantly affect the mechanical properties or the actuation angular speeds. More work into lowering the scaffold mechanical properties while increasing the actuation angular speed is necessary. Though the mechanical properties for the 83/17 and 40/60 scaffolds remained high compared to skeletal muscle, we also looked for differences in in vivo biocompatibility. Both scaffolds were implanted into the right vastus lateralis muscle of Sprague-Dawley rats. The left vastus lateralis muscle served as either the PBS injected sham surgery or an unoperated control. Biocompatibility was evaluated using enzymes, creatine kinase (CK) and lactate dehydrogenase (LDH), levels, fibrosis formation, inflammation, scaffold cellular infiltration, and neovascularization on days 7, 14, 21, and 28 post-implantation. Fibrotic tissue formation, inflammation, and elevated CK and LDH levels were observed initially but responses decreased during the four week study. Cells infiltrated the scaffolds and histological staining showed more fibroblasts than myogenic cells initially but over time, the fibroblasts decreased and myogenic cells increased. Neovascularization of both scaffolds was also recorded. PCL-MWCNT-PAA/PVA scaffolds were determined to be biocompatible, but some differences between the two types were noted. The 83/17 scaffolds caused less of a response from the body compared to the 40/60 scaffolds and had more myogenic cells attached. However, the 40/60 scaffolds had a larger number of blood vessels running through the scaffold. In conclusion, we have successfully fabricated a polymeric, conductive, and biocompatible scaffold that can actuate for skeletal muscle tissue engineering. Although our results are promising, more work is necessary to continue developing and refining the scaffold.
Design, Fabrication, and Characterization of Three Dimensional Complete Scaffolds for Bone Tissue Engineering
Andric, Tea (Virginia Tech, 2012-03-03)
Skeletal loss and bone deficiencies are major worldwide problem that is only expected to increase due to increase in aging population. As current standards in treatment autografts and allografts are not without drawbacks, there is a need for alternative bone grafts substitutes. The goal of this project was to utilize electrospinning and heat sintering techniques to create biodegradable full thickness three dimensional biomimetic polymeric scaffolds with macro and nano architecture similar to natural bone for bone tissue engineering. First we have investigated pretreatment with 0.1M NaOH and electrospinning gelatin/PLLA blends as means to increase overall mineral precipitation and distribution throughout the scaffolds when incubated in concentrated simulated body fluid (SBF)10XSBF. Mixture of 10% gelatin and PLLA resulted in the significantly higher degree of mineralization, increased mechanical properties, and scaffolds that supported cellular adhesion and proliferation. In the next step we applied heat sintering technique to fabricate 3D electrospun scaffolds that were used to evaluate effects of mineralization and fiber orientation on scaffold strength. Fiber orientation can make a slight difference in nanofibrous scaffold compressive mechanical properties, but this difference is not as profound as the difference seen with increased mineralization. We also developed a technique to fabricate scaffolds that mimic the organization of an osteon, the structural unit of cortical bone. Resulting scaffolds consisted of concentric layers of electrospun gelatin/PLLA nanofibers wrapped around microfiber core with diameters that ranged from 200-600µm. Individual osteon-like scaffolds were heat sintered to fabricate three dimensional scaffolds contained a system of channels running parallel to the length of the scaffolds, as found naturally in bone tissue. Finally we combined two previously fabricated structures, sintered electrospun sheets and individual osteon-like scaffolds, to create novel scaffolds that mimic dual structural organization of natural bone with cortical and trabecular regions. Mineralization for 24 hr significantly increased mechanical properties of the scaffolds, both yield stress and compressive modulus under physiological conditions. Both nonminerlized and mineralized scaffolds were found to support cellular attachment and proliferation over 28 days in culture, but scaffolds mineralized for 24hr were found to better support osteoblastic differentiation and mineral deposition.
Designing Scaffolds for Directed Cell Response in Tissue Engineering Scaffolds Fabricated by Vat Photopolymerization
Chartrain, Nicholas (Virginia Tech, 2019-12-04)
Vat photopolymerization (VP) is an additive manufacturing (AM) technology that permits the fabrication of parts with complex geometries and feature sizes as small as a few microns. These attributes make VP an attractive option for the fabrication of scaffolds for tissue engineering. However, there are few printable materials with low cytotoxicity that encourage cellular adhesion. In addition, these resins are not readily available and must be synthesized. A novel resin based on 2-acrylamido-2-methyl-1-propanesulfonic acid (NaAMPS) and poly(ethylene glycol) diacrylate (PEGDA) was formulated and printed using VP. The mechanical properties, water content, and high fidelity of the scaffold indicated promise for use in tissue engineering applications. Murine fibroblasts were observed to successfully adhere and proliferate on the scaffolds. The growth, migration, and differentiation of a cell is known to dependent heavily on its microenvironment. In engineered constructs, much of this microenvironment is provided by the tissue scaffold. The physical environment results from the scaffold's geometrical features, including pore shape and size, porosity, and overall dimensions. Each of these parameters are known to affect cell viability and proliferation, but due to the difficulty of isolating each parameter when using scaffold fabrication techniques such as porogen leaching and gas foaming, conflicting results have been reported. Scaffolds with pore sizes ranging from 200 to 600 μm were fabricated and seeded with murine fibroblasts. Other geometric parameters (e.g., pore shape) remained consistent between scaffold designs. Inhomogeneous cell distributions and fewer total cells were observed in scaffolds with smaller pore sizes (200-400 μm). Scaffolds with larger pores had higher cell densities that were homogeneously distributed. These data suggest that tissue scaffolds intended to promote fibroblast proliferation should be designed to have pore at least 500 μm in diameter. Techniques developed for selective placement of dissimilar materials within a single VP scaffold enabled spatial control over cellular adhesion and proliferation. The multi-material scaffolds were fabricated using an unmodified and commercially available VP system. The material preferences of murine fibroblasts which resulted in their inhomogeneous distribution within multi-material scaffolds were confirmed with multiple resins and geometries. These results suggest that multi-material tissue scaffolds fabricated with VP could enable multiscale organization of cells and material into engineered constructs that would mimic the function of native tissue.
Echogenic Biomaterials for Medical Ultrasound Tracking
Contreras, Jerry (Virginia Tech, 2020-06-29)
As the world population ages, hospital discharges of geriatric patients to nursing homes have increased. Patients with peripherally inserted central catheters (PICCs) are routinely discharged with the catheters in place. PICCs, only capable of being tracked through x-ray imaging, will routinely experience complications due to thrombosis or accidental dislodgement from poor at-home care. Routinely, elderly patients will be forced to revisit the hospital to have the catheter replaced using x-ray imaging, exposing them to hospital borne illness. Catheters with the capability to be tracked without the need of x-ray imaging would greatly benefit the ill and elderly, providing decreased stress to the patients and increase nursing home capabilities. This project seeks to develop the field of real-time ultrasound tracking of polymeric medical devices, through fabrication of ultrasound responsive polymer-glass composites. Optimal composition will be researched through three complimentary approaches. The first approach seeks to develop a polyurethane-glass microparticle composite to understand the relationship between microparticle loading and ultrasound imaging. In the second approach, manufacturing and end-use complications will be simulated to evaluate the effects on mechanical and ultrasonic properties. Furthermore, impacts from in-vitro long term catheterization to the sample mechanical and ultrasound morphologies would be analyzed. In the third approach, optimization from the previous approaches would assist in the replacement of medical grade polyurethane with medical grade thermoset silicone in hopes to prove the ability for the research to be transferable to other medical polymeric devices. The stated approaches will be useful for setting a path towards the development of ultrasonic imaging as the standard for medical device tracking.
Effect of Surface Chemistry and Young's Modulus on the Surface Motility of the Bacterium Pseudomonas Aeruginosa
Hittel, Jonathan Erwin (Virginia Tech, 2020-01-30)
This study demonstrates that the surface motility of the bacterium Pseudomonas aeruginosa is dependent on the surface chemistry of the underlying substrate. In particular, cells on hydrophobic polydimethylsiloxane (PDMS) have a speed that is on average 38% greater than on hydrophilic PDMS. These results were obtained using time-lapse microscopy of bacteria exposed to continuously flowing tryptic soy broth growth medium at 37 ⁰C. Not only are the mean speeds different, the distributions of speeds are also different: on the hydrophobic substrate, a smaller proportion of bacteria move by less than about one body-length (~3 µm) in 60 minutes. In addition, the surface chemistry affects the orientation of the cells: there is a greater fraction of "walking" bacteria on the hydrophobic surface. Sensitivity to the substrate surface chemistry occurs despite the presence of a complex mix of substances in the growth medium and offers hope that surface chemistry can be used to tune motility and the progression to biofilm formation. Additionally, the effect of reducing the near-surface Young's modulus of the PDMS from 7000 to 70 kPA is investigated. For the lower modulus material, there is an increase in the likelihood of a bacterium executing sudden, high angle turns. This is evident in images with a framerate of one frame per 0.22s. However, the impact of these turns is averaged out over longer times such that the mean speed over periods of more than about one minute is the same for bacteria on both the high and the low modulus materials. Consequently, except over very short time intervals, Young's modulus in the surface region is not effective as a means of modulating motile behavior.
Effects of Keratin Biomaterial Therapeutics on Cellular and Inflammatory Mechanisms in Injury and Disease Models
Waters, Michele (Virginia Tech, 2018-06-11)
Keratins are fibrous structural proteins found in human hair that have been used to develop bioactive and biocompatible constructs for a wide variety of tissue engineering and healthcare applications. Their ubiquity, capacity for self-assembly, ease of use and versatility in blended materials, and ability to modulate cell behavior and promote tissue ingrowth have made keratins well-suited for the development of regenerative therapies. In particular, keratins have demonstrated bioactivity in both in-vivo and in-vitro studies, by altering immune and stem cell phenotype and function and promoting an anti-inflammatory/wound healing environment. This work seeks to build on previous research by investigating the ability of low and high molecular weight keratins to augment anti-inflammatory primary macrophage phenotypes and examining the influence of keratin biomaterials on cellular and inflammatory mechanisms in two models of injury and disease. Rodent models of blast induced neurotrauma (BINT) and severe osteoporosis were used to inform the development of 2D and 3D in-vitro models of macrophage/endothelial cell injury and osteogenic differentiation respectively. Keratin biomaterials exhibited some potential to alter macrophage and endothelial cell dynamics following blast, specifically by promoting anti-inflammatory (M2c-like) macrophage polarization and diminishing endothelial cell injury responses (i.e. endothelial glycocalyx shedding). A more clinically relevant model of osteoporosis found that stem cells harvested from older, osteoporotic animals demonstrated limited proliferative and bone differentiation potential compared to healthy cells. However, 3D constructs (especially keratin-based materials) were able to enhance calcification and osteogenic gene expression of diseased cells. These results highlight the complexity of macrophage phenotypic switching and cellular dynamics in these systems. However, keratin-based therapeutics may prove useful for facilitating tissue regeneration and limiting detrimental inflammatory and cellular responses in various models of injury and disease.
Effects of Therapeutic Radiation on Polymeric Scaffolds
Cooke, Shelley L. (Virginia Tech, 2014-01-16)
High levels of ionizing radiation are known to cause degradation and/or cross-linking in polymers. Lower levels of ionizing radiation, such as x-rays, are commonly used in the treatment of cancers. Material characterization has not been fully explored for polymeric materials exposed to therapeutic radiation levels. This study investigated the effects of therapeutic radiation on three porous scaffolds: polycaprolactone (PCL), polyurethane (PU) and gelatin. Porous scaffolds were fabricated using solvent casting and/or salt leaching techniques. Scaffolds were placed in phosphate buffered saline (PBS) and exposed to a typical cancer radiotherapy schedule. A total dose of 50 Gy was broken into 25 dosages over a three-month period. PBS was collected over time and tested for polymer degradation through high performance liquid chromatography (HPLC) and bicinchoninic acid (BCA) protein assay. Scaffolds were characterized by changes in microstructure using Scanning Electron Microscopy (SEM), and crystallization using Differential Scanning Calorimetry (DSC). Additionally, gelatin ε-amine content was analyzed using Trinitrobenzene Sulfonic Acid Assay (TNBSA). Gelatin scaffolds immersed in PBS for three months without radiation served as a control. Each scaffold responded differently to radiation. PCL showed no change in molecular weight or microstructure. However, the degree of crystallinity decreased 32% from the non-irradiated control. PU displayed both changes in microstructure and a decrease in crystallinity (85.15%). Gelatin scaffolds responded the most dramatically to radiotherapy. Samples were observed to swell, yet maintain shape after exposure. As gelatin was considered a tissue equivalent, further studies on tissues are needed to better understand the effects of radiotherapy.
Electrospun Nanocellulose: A New Biomaterial
Rodriguez Rivera, Katia Argelia (Virginia Tech, 2011-09-23)
Science and engineering studies on biocompatible implantable materials for tissue and organ repair have recently focused on polymeric materials to serve as scaffolds for cellular integration. Cellulose in many forms has been demonstrated as potential biopolymer for tissue engineering; however, it has not been previously electrospun into a scaffold for tissue engineering applications. The overall goal of this research project was to produce electrospun cellulose acetate (CA) nanofibers with specific architectures and surface chemistries to be evaluated as scaffolds for tissue regeneration. The size and morphology of electrospun CA was impacted by polymer concentration, solvent system, and solution flow rate. The conversion of CA electrospun scaffolds into regenerated cellulose by exposure to NaOH ethanol solution was successful for scaffolds produced at polymer solution flow rate of at least 1 mL/h. The regeneration process resulted in minimal degradation of the cellulose while retaining the original fiber structure of the scaffold. In vitro cytotoxicity evaluation of the fibrous cellulose scaffolds on a culture of mouse fibroblast (L-929) cells indicated that this material posed no threat to mammalian cells. Electrospun cellulose scaffolds with different architectures and surface chemistries were designed and evaluated to enhance scaffold properties and cell adhesion. The morphology of the partially regenerated cellulose revealed only a broad diffraction peak for the scaffold material, while the fully regenerated cellulose showed a characteristic semi-crystalline cellulose II diffraction pattern. Fiber orientation and porosity of the scaffolds were controlled by electrospining CA solution onto the edge of a rotator wheel and laser microablation, respectively. Bioactivity of the scaffolds was shown to be enhanced via scaffold surface modification with either anionic or cationic functional groups. Biomimetic Ca-P crystal mineralization on electrospun cellulose fibers was produced by means of carboxymethyl cellulose (CMC) adsorption and treatments with simulated body fluid (SBF) or phosphate buffer saline (PBS) solutions. Porosity and Ca-P crystals enhanced osteoprogenitor cell adhesion on the electrospun cellulose scaffolds. Cationic modification by trimethyl ammonium betahydroxy propyl (THAMP) derivation and adsorption of extracellular matrix proteins on cellulose fibers promoted adhesion and proliferation of neural-like (PC12) and myoblast (C2C12) cells. Differentiation of myoblast cells (C2C12) towards myotubes on electrospun cellulose scaffolds was controlled by surface chemistry and mechanical properties. Together these studies showed great potential for cellulose acetate to be electrospun and converted into a viable biocompatible tissue engineering scaffolds.
Evaluating the Time-Dependent Melting Behavior of Semicrystalline Polymers Through Strobl's 3-Phase Model
Hoang, Jonathan Dan (Virginia Tech, 2013-03-28)
The melting behavior of polymers can provide information on their crystallization mechanism. However, the origin of the time-dependent low endotherm, or annealing peak, and the extent of melting-recrystallization-remelting during heating are still debated. The crystallization and subsequent melting behavior of isotactic polystyrene are explored in the context of Stroblâ "s 3-Phase model using differential scanning calorimetry (DSC), small angle X-ray scattering (SAXS), and wide angle X-ray diffraction. DSC experiments confirm the existence of a crystallization time-dependent low endotherm, and melting-recrystallization-remelting processes during heating. SAXS analysis using the correlation function confirms that the lamellar thickness increases with crystallization temperature and is independent of time. The spread between equilibrium melting and crystallization temperatures determined in this work (Tfâ"" = 533K, Tcâ"" = 544K) is much smaller than reported by Strobl et al. (Tfâ"" = 562K, Tcâ"" = 598K). These differences are partially attributed to overestimation in lamellar thicknesses calculated through the interface distribution function. Analysis of diffraction broadening shows that the apparent crystal size decreases with crystallization time, suggesting the formation of smaller/less perfect crystals during secondary crystallization. These results are consistent with observations that the glass transition temperature increases with crystallization time and supports the idea that secondary crystallization leads to increased amorphous conformational constraints. These results also suggest that the upward shift of the annealing peak during secondary crystallization is associated with increased amorphous constraints rather than increased crystal dimensions. The lack of distinction between Tfâ"" and Tcâ"" and the evolution of crystal size during crystallization stand in direct contrast with Stroblâ "s model.
Extension of the Method of Ellipses to Determining the Orientation of Long, Semi-flexible Fibers in Model 2- and 3-dimensional Geometries
Hofmann, John (Virginia Tech, 2013-10-23)
The use of fiber-reinforced polymer composites formed via injection molding is of increasing interest due to their superior mechanical properties as compared to those of the polymer matrix alone. These mechanical properties, however, are strongly dependent on the fiber length and orientation distributions within a molded part. As such, there is a need to understand and model the orientation evolution of chopped fibers in flow in order to accurately simulate the final fiber orientation distribution within injection molded parts. As a result of this, accurate and reliable experimental measurement of fiber orientation is needed. Within this research, the application and validity of the Method of Ellipses for determining the orientation of long, semi-flexible glass fibers within injection molded composites has been investigated. A fiber suspension with an average length of approximately 3.9 mm was the focus of this study and assumed to be representative of commercial distributions. A novel method to quantify fiber curvature was developed and utilized to show that flexibility in center-gated disc and the end-gated plaque samples was minimal on average for the selected fiber length distribution. Thus, it was determined that the Method of Ellipses was applicable when utilized to obtain reliable orientation data for the selected long glass fiber suspension and within the chosen geometries that exhibit 1-, 2-, and 3-dimensional velocity fields. However, a modified image analysis width was found to be necessary in regions of highly aligned fibers, due to the increase in ellipse size and the need to reduce the number of partial objects and thus minimize error. This allowed for a direct comparison of the experimental orientation behavior of short and long glass fibers within the center-gated disc and the end-gated plaque, as well as the effect of the orientation distributions on the global modulus of the part.
Fabrication and Characterization of Three Dimensional Electrospun Cortical Bone Scaffolds
Andric, Tea; Taylor, Brittany L.; Degen, Katherine E.; Whittington, Abby R.; Freeman, Joseph W. (De Gruyter Open, 2014)
Bone is a composite tissue composed of an organic matrix, inorganic mineral matrix and water. Structurally, bone is organized into two distinct types: trabecular (or cancellous) and cortical (or compact) bone. Cortical bone is highly organized, dense and composed of tightly packed units or osteons whereas trabecular bone is highly porous and usually found within the confines of cortical bone. Osteons, the subunits of cortical bone, consist of concentric layers of mineralized collagen fibers. While many scaffold fabrication techniques have sought to replicate the structure and organization of trabecular bone, very little research focuses on mimicking the organization of native cortical bone. In this study we fabricated three-dimensional electrospun cortical scaffolds by heat sintering individual osteon-like scaffolds. The scaffolds contained a system of channels running parallel to the length of the scaffolds, as found naturally in the haversian systems of bone tissue. The purpose of the studies discussed in this paper was to develop a mechanically enhanced biomimetic electrospun cortical scaffold. To that end we investigated the appropriate mineralization and cross-linking methods for these structures and to evaluate the mechanical properties of scaffolds with varying fiber angles. Cross-linking the gelatin in the scaffolds prior to the mineralization of the scaffolds proved to help prevent channels of the osteons from collapsing during fabrication. Premineralization, before larger scaffold formation and mineralization, increased mineral deposition between the electrospun layers of the scaffolds. A combination of cross-linking and premineralization significantly increased the compressive moduli of the individual scaffolds. Furthermore, scaffolds with fibers orientation ranging between 15° and 45° yielded the highest compressive moduli and yield strength.
Fabrication, Characterization and Cellular Interactions of Keratin Nanomaterial Coatings for Implantable Percutaneous Prosthetics
Trent, Alexis Raven (Virginia Tech, 2018-04-16)
Implantable medical devices face numerous complications when interfacing with soft tissue, and are plagued by negative responses from host tissue. One such class devices are percutaneous osseointegrated prosthetics (POP). POP consist of a bone anchored titanium post that extrudes through the skin and attaches to an external prosthetic. Compared to the traditional socket interface, POPs offer better stability, limb functionality, and osseoperception for both upper and lower prosthetic limbs. Although the POP surgery technique is well established, the main disadvantage to this technology remains the titanium (Ti) - skin interface. Some of the complications that can arise include epithelial downgrowth, mechanical tearing, and infection. Various types of coatings, surface structure, and antibiotic release technologies have been used to coat Ti in an effort to mitigate POP's associated obstacles, but these methods have failed to translate into published clinical studies and mainstream medical use. One potential solution may be to mimic an interface already found in the human body, the fingernail-skin interface, which is infection-free and mechanically stable. The same keratins that make up the cortex of human hair fibers are found in the fingernail. These cortical human hair keratins can be extracted and purified, and fingernail-specific dimeric complexes coated onto Ti surfaces using silane coupling chemistry. Keratin has been used in other studies for its cell adhesion and differentiation properties, and it has been suggested that the Leu-Asp-Val (LDV) amino acid motif is the primary site responsible for cellular attachment. In the present work, keratins extracted from human hair fibers and recombinant keratin nanomaterials (KN) were used to create biomimetic coatings on silanized Ti surfaces. These coatings were characterized and investigated for surface topography, elemental composition, cell adhesion motifs, and cell adhesion. Both keratin substrates showed the ability to create uniform coatings that retain a protein conformation that exhibits cell adhesion motifs. The coatings exhibit the ability to support cell adhesion of both epithelial and connective tissue cells. Application of fluid shear stress was used to test the mechanical adhesion strength of cells on keratin coatings. The structure, biochemical stability and sustained cellular adhesion of these coatings support keratin's capacity to provide a stable interface between POPs and skin. Side-by-side studies of extracted and recombinant keratins reveals that the recombinant form of these materials may provide distinct advantages for their use in POP devices. Overall, this study confirmed that a uniform, silane-coupled keratin coating was feasible. We demonstrated the substrates contain a biological function in terms of cellular adhesion and phenotypic changes in skin-relevant cells. These results support the biomimetic function of keratin on silanized Ti, which may provide a suitable coating to translate percutaneous medical device coating applications toward clinical use.
Focused Ultrasound Biofilm Ablation: Investigation of Histotripsy for the Treatment of Catheter-Associated Urinary Tract Infections (CAUTIs)
Childers, Christopher; Edsall, Connor; Gannon, Jessica; Whittington, Abby R.; Muelenaer, Andre A.; Rao, Jayasimha; Vlaisavljevich, Eli (IEEE, 2021-09-01)
Urinary catheters often become contaminated with biofilms, resulting in catheter-associated urinary tract infections (CAUTIs) that adversely affect patient outcomes. Histotripsy is a non-invasive focused ultrasound therapy previously developed for the non-invasive ablation of cancerous tumors and soft tissues. Histotripsy has also previously shown the ability to treat biofilms on glass slides and surgical meshes. Here, we investigate the potential of histotripsy for the treatment of CAUTIs for the first time in vitro. Clinically relevant catheter materials (Tygon, Silicone, and latex catheter mimics) and commonly used clinical catheters were tested to determine the feasibility of producing luminal histotripsy bubble clouds. A Pseudomonas aeruginosa (strain PA14) biofilm model was developed and tested to produce luminal biofilms in an in vitro Tygon catheter mimic. This model was treated with histotripsy to determine the ability to remove a luminal biofilm. Finally, the bactericidal effects of histotripsy were tested by treating PA14 suspended inside the Tygon catheter mimic. Results showed that histotripsy produced precise luminal cavitation within all tested catheter mimics and clinical catheters. Histotripsy treatment of a PA14 biofilm with histotripsy reduced luminal biofilm OD590 signal down to background levels. Further, the treatment of suspended PA14 in LB showed a 3.45±0.11 log10 reduction in CFU/mL after 6 histotripsy scans across the catheter mimics. Overall, the results of this study demonstrate the potential of histotripsy to provide a new modality for removing bacterial biofilms from catheter-based medical devices and suggest that additional work is warranted to investigate histotripsy for the treatment of CAUTIs and other biomaterial-associated infections.

Browsing by Author "Whittington, Abby R."

Results Per Page

Sort Options