Show simple item record

dc.contributor.authorGu, Hongmeien
dc.date.accessioned2014-03-14T20:16:08Zen
dc.date.available2014-03-14T20:16:08Zen
dc.date.issued2001-08-09en
dc.identifier.otheretd-09112001-113739en
dc.identifier.urihttp://hdl.handle.net/10919/28938en
dc.description.abstractThe importance of precise values for the parameters used in heat and mass transfer models has been demonstrated by many research studies. Thermal conductivity values used in previous models are usually empirical and fluctuate. Theoretical analysis and estimations of wood thermal conductivities in the radial and tangential directions were conducted with the geometric models built up from the macro- and micro-structure observations. Theoretically, thermal conductivity in the radial direction is about 1.5 to 2.5 times of the tangential direction for softwood species with moisture content (MC) below Fiber Saturation Point (FSP). When MC is over the FSP, tangential radial thermal conductivity both increase dramatically and are linear function of MC. The two thermal conductivity values are close with a ratio of near one estimated by the model for MC above the FPS. In hardwood species, radial thermal conductivity estimated by the model is 1.5 times of the tangential thermal conductivity. Validation tests for model estimations of thermal conductivities in the radial and tangential directions for three wood species showed the reliability of the geometric models developed in this project. Correlations between the wood thermal conductivity and structure parameters, such as latewood percentage and cell wall percentage, were examined. Linear relationships for the thermal conductivity and average temperature in wood were established in both radial and tangential directions of three wood species. A two-dimensional transient heat conduction model was developed utilizing thermal conductivity values derived from geometric models. The anisotropic material property affect on heat transport in radial and tangential directions was discussed using an assumed situation. The simulation run showed slightly faster heat flow in the radial direction than in the tangential direction due to higher thermal conductivity in the radial direction. Validation tests on practical wood blocks showed the 2D model with the use of theoretical thermal conductivity values can predict good temperature distribution in wood during the heating process. However, in the practical wood samples with curved rings on the cross section, no significant difference was found in the two transverse directions. Mathematica software was introduced in this study for the intense and complicated math calculations and model programming. Mathematica was found to be a powerful technique for solving sophisticated math problems. It had abundant and flexible plotting options for providing optimized presentations for the results. These advantages make Mathematica popular for engineering modeling research.en
dc.publisherVirginia Techen
dc.relation.haspart06chapterOne.pdfen
dc.relation.haspart09ChapterTwo-5and6.pdfen
dc.relation.haspart00FrontPage.pdfen
dc.relation.haspart04TOF.pdfen
dc.relation.haspart01Abstract.pdfen
dc.relation.haspart05TOT.pdfen
dc.relation.haspart07ChapterTwo-1and2.pdfen
dc.relation.haspart13AppendixA.pdfen
dc.relation.haspart11ChapterFour.pdfen
dc.relation.haspart10ChapterThree.pdfen
dc.relation.haspart12Vita.pdfen
dc.relation.haspart02Acknowledgement.pdfen
dc.relation.haspart03TOC.pdfen
dc.relation.haspart14AppendixB.pdfen
dc.relation.haspart08ChapterTwo-3and4.pdfen
dc.rightsIn Copyrighten
dc.rights.urihttp://rightsstatements.org/vocab/InC/1.0/en
dc.subjectGeometric modelingen
dc.subjectFinite differenceen
dc.subjectnumerical modelen
dc.subjectThermal conductivityen
dc.subjectAnatomical structureen
dc.titleStructure Based, Two-dimensional, Anisotropic, Transient Heat Conduction model for Wooden
dc.typeDissertationen
dc.contributor.departmentWood Science and Forest Productsen
dc.description.degreePh. D.en
thesis.degree.namePh. D.en
thesis.degree.leveldoctoralen
thesis.degree.grantorVirginia Polytechnic Institute and State Universityen
thesis.degree.disciplineWood Science and Forest Productsen
dc.contributor.committeechairZink-Sharp, Audrey G.en
dc.contributor.committeememberYoungs, Robert L.en
dc.contributor.committeememberDiller, Thomas E.en
dc.contributor.committeememberLamb, Fred M.en
dc.contributor.committeememberKamke, Frederick A.en
dc.identifier.sourceurlhttp://scholar.lib.vt.edu/theses/available/etd-09112001-113739/en
dc.date.sdate2001-09-11en
dc.date.rdate2002-09-13en
dc.date.adate2001-09-13en


Files in this item

Thumbnail
Thumbnail
Thumbnail
Thumbnail
Thumbnail
Thumbnail
Thumbnail
Thumbnail
Thumbnail
Thumbnail
Thumbnail
Thumbnail
Thumbnail
Thumbnail
Thumbnail

This item appears in the following Collection(s)

Show simple item record