Assessment of a Leading Edge Fillet for Decreasing Vane Endwall Temperatures in a Gas Turbine Engine

dc.contributor.authorLethander, Andrew Taiten
dc.contributor.committeechairThole, Karen A.en
dc.contributor.committeememberGrossman, Bernard M.en
dc.contributor.committeememberO'Brien, Walter F. Jr.en
dc.contributor.committeememberNg, Faien
dc.contributor.committeememberDiller, Thomas E.en
dc.contributor.departmentMechanical Engineeringen
dc.date.accessioned2014-03-14T20:20:03Zen
dc.date.adate2003-12-10en
dc.date.available2014-03-14T20:20:03Zen
dc.date.issued2003-12-01en
dc.date.rdate2005-12-10en
dc.date.sdate2003-12-09en
dc.description.abstractThe objective of this investigation was to improve the thermal environment for a turbine vane through reduction of passage secondary flows. This was accomplished by modifying the vane/endwall junction to include a leading edge fillet. The problem approach was to integrate optimization methods with computational fluid dynamics to optimize the fillet design. The resulting leading edge fillet was then tested in a large-scale, low speed cascade to verify thermal performance. A combustor simulator located upstream of the cascade was used to generate realistic inlet conditions for the turbine vane. Both computational and experimental results underscore the importance of properly modeling the inlet conditions to the turbine. Results of the computational optimization process indicate that significant reductions in adiabatic wall temperature can be achieved with a leading edge fillet. While the intent of the initial fillet design was to improve the thermal environment for the vane endwall, computational results also indicate thermal benefit to the vane surfaces. Flow and thermal field results show that a fillet can enhance coolant effectiveness, prevent formation of the leading edge horseshoe vortex, and preclude full development of a passage vortex. In experimental testing, four cascade inlet conditions were investigated to evaluate the effectiveness of the fillet in reducing endwall temperature levels. Two tested conditions featured a flush combustor/cascade interface, while the remaining two included coolant injection through a backward-facing slot. With the flush interface, fillet thermal performance was evaluated for two inlet total pressure profiles. For the design profile, the fillet had a positive impact on the endwall temperature distribution as well as on the passage thermal field. For the off-design profile, the fillet was observed to have a slightly detrimental impact on the endwall adiabatic temperature distribution; however, passage thermal field results indicate a thermal benefit for the vane suction surface. With the backward-facing slot, thermal tests were conducted for two slot coolant flow rates. For both slot flow rates, the fillet improved endwall thermal protection and prevented coolant lift-off. While increasing the flow rate of slot coolant enhanced endwall effectiveness, fillet thermal performance was similar for the two slot flow rates.en
dc.description.degreePh. D.en
dc.identifier.otheretd-12092003-144152en
dc.identifier.sourceurlhttp://scholar.lib.vt.edu/theses/available/etd-12092003-144152/en
dc.identifier.urihttp://hdl.handle.net/10919/30011en
dc.publisherVirginia Techen
dc.relation.haspart02CHAPTER1.pdfen
dc.relation.haspart03CHAPTER2.pdfen
dc.relation.haspart08CHAPTER7.pdfen
dc.relation.haspart09REFERENCES.pdfen
dc.relation.haspart10APPENDICES.pdfen
dc.relation.haspart05CHAPTER4.pdfen
dc.relation.haspart04CHAPTER3.pdfen
dc.relation.haspart06CHAPTER5.pdfen
dc.relation.haspart01TOC.pdfen
dc.relation.haspart07CHAPTER6.pdfen
dc.relation.haspart11VITA.pdfen
dc.rightsIn Copyrighten
dc.rights.urihttp://rightsstatements.org/vocab/InC/1.0/en
dc.subjectPropulsionen
dc.subjectGas Turbineen
dc.subjectHeat--Transmissionen
dc.titleAssessment of a Leading Edge Fillet for Decreasing Vane Endwall Temperatures in a Gas Turbine Engineen
dc.typeDissertationen
thesis.degree.disciplineMechanical Engineeringen
thesis.degree.grantorVirginia Polytechnic Institute and State Universityen
thesis.degree.leveldoctoralen
thesis.degree.namePh. D.en
Files
Original bundle
Now showing 1 - 5 of 11
Loading...
Thumbnail Image
Name:
01TOC.pdf
Size:
330.83 KB
Format:
Adobe Portable Document Format
Loading...
Thumbnail Image
Name:
02CHAPTER1.pdf
Size:
273.47 KB
Format:
Adobe Portable Document Format
Loading...
Thumbnail Image
Name:
03CHAPTER2.pdf
Size:
807.78 KB
Format:
Adobe Portable Document Format
Loading...
Thumbnail Image
Name:
04CHAPTER3.pdf
Size:
671.42 KB
Format:
Adobe Portable Document Format
Loading...
Thumbnail Image
Name:
05CHAPTER4.pdf
Size:
1.14 MB
Format:
Adobe Portable Document Format