VTechWorks staff will be away for the winter holidays starting Tuesday, December 24, 2024, through Wednesday, January 1, 2025, and will not be replying to requests during this time. Thank you for your patience, and happy holidays!
 

Structural Performance of High Strength Lightweight Concrete Pretensioned Bridge Girders

Simple item page
dc.contributor.authorCross, Benjamin Thomasen
dc.contributor.committeecochairCousins, Thomas E.en
dc.contributor.committeecochairRoberts-Wollmann, Carin L.en
dc.contributor.committeememberEasterling, William Samuelen
dc.contributor.committeememberSotelino, Elisa D.en
dc.contributor.departmentCivil Engineeringen
dc.date.accessioned2014-03-14T20:07:21Zen
dc.date.adate2012-03-02en
dc.date.available2014-03-14T20:07:21Zen
dc.date.issued2012-02-01en
dc.date.rdate2012-03-02en
dc.date.sdate2012-02-13en
dc.description.abstractThe use of high compressive strengths in prestressed bridge girders can lower costs by allowing for longer spans, increased girder spacing, and smaller cross-sections. If high strength lightweight concrete (HSLWC) is used, these advantages are further enhanced due to the corresponding reduction in self-weight. Additional benefits can then be realized in the form of more traffic lanes, increased load capacity, smaller substructures, reduced crane capacity requirements, and lower shipping costs. Despite the possible economic savings, HSLWC has been used infrequently in prestressed bridge girder applications across the nation. While recent research has been performed to extend the applicability of current bridge design specifications to normal weight concretes with strengths as high as 18 ksi, little has been done by comparison with regards to HSLWC. The purpose of the research in this report was to assess whether current bridge design specifications for transfer length, development length, prestress loss, camber, and flexural capacity are satisfactory for use with fully-bonded, pretensioned flexural members consisting of HSLWC and to make recommendations for improvements where necessary. Twelve high strength pretensioned beams of variable unit weight (eight lightweight beams and four normal weight beams) and strand size (eight beams with 0.5-in. strand and four beams with 0.6-in. strand) were cast at the Thomas M. Murray Structural Engineering Laboratory at Virginia Tech. These beams were allowed to sit for a period of several months after fabrication while measurements were taken regarding transfer length, prestress loss, and camber. After this period, the beams were load tested to collect development length data, flexural data, and further data related to prestress loss. In addition to the laboratory cast beams, prestress loss and camber data from six full-size bridge beams (five lightweight beams and one normal weight beam) cast as part of a separate project at Virginia Tech was examined. Analysis of the results for all beams shows that with a few caveats, the current AASHTO LRFD Specifications and other design methods examined regarding the topics under consideration are satisfactory for use in the design of HSLWC pretensioned bridge girders with properties similar to those of the beams studied.en
dc.description.degreePh. D.en
dc.identifier.otheretd-02132012-005741en
dc.identifier.sourceurlhttp://scholar.lib.vt.edu/theses/available/etd-02132012-005741/en
dc.identifier.urihttp://hdl.handle.net/10919/26190en
dc.publisherVirginia Techen
dc.relation.haspartCross_BT_D_2012.pdfen
dc.relation.haspartCross_BT_D_2012_Copyright.pdfen
dc.rightsIn Copyrighten
dc.rights.urihttp://rightsstatements.org/vocab/InC/1.0/en
dc.subjectprestress lossen
dc.subjectdevelopment lengthen
dc.subjecttransfer lengthen
dc.subjecthigh strength concreteen
dc.subjectlightweight concreteen
dc.subjectcamber growthen
dc.subjectpretensioned girdersen
dc.titleStructural Performance of High Strength Lightweight Concrete Pretensioned Bridge Girdersen
dc.typeDissertationen
thesis.degree.disciplineCivil Engineeringen
thesis.degree.grantorVirginia Polytechnic Institute and State Universityen
thesis.degree.leveldoctoralen
thesis.degree.namePh. D.en

Files

Original bundle
Now showing 1 - 2 of 2
Thumbnail Image
Name:
Cross_BT_D_2012.pdf
Size:
17.95 MB
Format:
Adobe Portable Document Format
Download
Thumbnail Image
Name:
Cross_BT_D_2012_Copyright.pdf
Size:
4.22 MB
Format:
Adobe Portable Document Format
Download

Collections

Doctoral Dissertations