An Exploratory Study of the Application of Carbon Nanotubes to Skin Friction Measurements
| dc.contributor.author | Henderson, Bancroft W. | en |
| dc.contributor.committeechair | Schetz, Joseph A. | en |
| dc.contributor.committeemember | Johnson, Eric R. | en |
| dc.contributor.committeemember | Safaai-Jazi, Ahmad | en |
| dc.contributor.department | Aerospace and Ocean Engineering | en |
| dc.date.accessioned | 2014-03-14T20:41:49Z | en |
| dc.date.adate | 2004-08-10 | en |
| dc.date.available | 2014-03-14T20:41:49Z | en |
| dc.date.issued | 2004-07-16 | en |
| dc.date.rdate | 2005-08-10 | en |
| dc.date.sdate | 2004-07-23 | en |
| dc.description.abstract | A small shear sensor utilizing an array of carbon nanotubes to support a sensor head was developed for use in steady, high speed, 2D flow. The sensor is a non-intrusive, direct measurement device with a 2 x 2 mm square sensor head surrounded by a small gap on each side (~0.004 inches). The translation of the sensing element is due to the nanotubes bending when a shear force is applied to the sensor head. Displacements are measured by an interferometric technique using fiber-optics to measure the distance the sensor head travels by viewing a polished side of the head. The fiber-optical displacement sensor is bonded to a stationary substrate so that all measurements are relative to a fixed position. Arrays of carbon nanotubes were grown on bare 2 x 2 mm square silicon chips. The nanotubes were grown to heights of 75 microns with a thin layer of amorphous carbon on top. The silicon chips were then flipped, and the amorphous layer of carbon was bonded to bare 1 x 1 cm silicon substrates, making the bottom of 2 x 2 mm silicon chip the sensor head. The sensors were calibrated at Luna Innovations using a point-load technique. Four of the six sensors could not be successfully calibrated because they were fatally damaged during the last step of the calibration process. Wind tunnel tests were conducted on the one sensor that survived the calibration. An arrangement was designed and built from aluminum to test the performance of the sensor in the Virginia Tech Supersonic Wind Tunnel. Seven test runs were conducted in this cold-flow facility at a nominal Mach number of 2.4 and stagnation pressures ranging from 50 - 90 psia. Two test runs gave skin friction values 3 - 20% lower than those values predicted by indirect measurement techniques before the sensor was damaged. While these first results are encouraging, further studies are clearly needed. Due to distinct anomalies in the displacement data during test run 3, it was concluded that the sensor was damaged during this run. Possible explanations of the failure of this sensor are offered along with suggestions for future work. | en |
| dc.description.degree | Master of Science | en |
| dc.identifier.other | etd-07232004-084236 | en |
| dc.identifier.sourceurl | http://scholar.lib.vt.edu/theses/available/etd-07232004-084236/ | en |
| dc.identifier.uri | http://hdl.handle.net/10919/34119 | en |
| dc.publisher | Virginia Tech | en |
| dc.relation.haspart | Thesis.pdf | en |
| dc.rights | In Copyright | en |
| dc.rights.uri | http://rightsstatements.org/vocab/InC/1.0/ | en |
| dc.subject | fiber optic | en |
| dc.subject | skin friction | en |
| dc.subject | nanotubes | en |
| dc.subject | shear stress | en |
| dc.title | An Exploratory Study of the Application of Carbon Nanotubes to Skin Friction Measurements | en |
| dc.type | Thesis | en |
| thesis.degree.discipline | Aerospace and Ocean Engineering | en |
| thesis.degree.grantor | Virginia Polytechnic Institute and State University | en |
| thesis.degree.level | masters | en |
| thesis.degree.name | Master of Science | en |
Files
Original bundle
1 - 1 of 1