Integrated Thermal Design and Optimization Study for Active Integrated Power Electronic Modules (IPEMs)

Simple item page
dc.contributor.authorPang, Ying-Fengen
dc.contributor.committeechairScott, Elaine P.en
dc.contributor.committeecochairThole, Karen A.en
dc.contributor.committeememberBohn, Jan Helgeen
dc.contributor.departmentMechanical Engineeringen
dc.date.accessioned2014-03-14T20:44:57Zen
dc.date.adate2002-09-11en
dc.date.available2014-03-14T20:44:57Zen
dc.date.issued2002-08-26en
dc.date.rdate2003-09-11en
dc.date.sdate2002-09-08en
dc.description.abstractThermal management is one of many critical tasks in the design of power electronic systems. It has become increasingly important as a result of the introduction of high power density and integrated modules. It has also been realized that higher temperatures do affect reliability due to a variety of physical failure mechanisms that involve thermal stresses and material degradation. Therefore, it is important to consider temperature as design parameter in developing power electronic modules. The NSF Center for Power Electronics System (CPES) at Virginia Tech previously developed a first generation (Gen-I) active Integrated Power Electronics Module (IPEM). This module represents CPES's approach to design a standard power electronic module with low labor and material costs and improved reliability compared to industrial Intelligent Power Modules (IPM). A preliminary Generation II (Gen-II.A) active IPEM was built using embedded power technology, which removes the wire bonds from the Gen-I IPEM. In this module, the three primary heat-generating devices are placed on a direct bonded copper substrate in a multi-chip module format. The overall goal of this research effort was to optimize the thermal performance of this Gen-II.A IPEM. To achieve this goal, a detailed three-dimensional active IPEM was modeled using the thermal-fluid analysis program ESC in I-DEAS to study the thermal performance of the Gen-II.A IPEM. Several design variables including the ceramic material, the ceramic thickness, and the thickness of the heat spreader were modeled to optimize IPEM geometric design and to improve the thermal performance while reducing the footprint. Input variables such as power loss and interface material thicknesses were studied in a sensitivity and uncertainty analysis. Other design constraints such as electrical design and packaging technology were also considered in the thermal optimization of the design. A new active IPEM design named Gen-II.C was achieved with reduced-size and improved thermal and electrical performance. The success of the new design will enable the replacement of discrete components in a front-end DC/DC converter by this standard module with the best thermal and electrical performance. Future improvements can be achieved by replacing the current silicon chip with a higher thermal-conductivity material, such as silicon carbide, as the power density increases, and by, exploring other possible cooling techniques.en
dc.description.degreeMaster of Scienceen
dc.identifier.otheretd-09082002-125724en
dc.identifier.sourceurlhttp://scholar.lib.vt.edu/theses/available/etd-09082002-125724/en
dc.identifier.urihttp://hdl.handle.net/10919/34965en
dc.publisherVirginia Techen
dc.relation.haspartThesis_Pang.pdfen
dc.rightsIn Copyrighten
dc.rights.urihttp://rightsstatements.org/vocab/InC/1.0/en
dc.subjectpower electronics coolingen
dc.subjectintegrated design optimizationsen
dc.subjectthermal managementen
dc.titleIntegrated Thermal Design and Optimization Study for Active Integrated Power Electronic Modules (IPEMs)en
dc.typeThesisen
thesis.degree.disciplineMechanical Engineeringen
thesis.degree.grantorVirginia Polytechnic Institute and State Universityen
thesis.degree.levelmastersen
thesis.degree.nameMaster of Scienceen

Files

Original bundle
Now showing 1 - 1 of 1
Thumbnail Image
Name:
Thesis_Pang.pdf
Size:
1.91 MB
Format:
Adobe Portable Document Format
Download

Collections

Masters Theses